Maytag 27" Troubleshooting Manual

Download Troubleshooting manual of Maytag 27" Washer for Free or View it Online on All-Guides.com.

Brand: Maytag

Category: Washer

Type: Troubleshooting manual for Maytag 27"

Pages: 36

Download Maytag 27" Troubleshooting manual

Maytag 27
1
Maytag 27
2
Maytag 27
3
Maytag 27
4
Maytag 27
5
Maytag 27
6
Maytag 27
7
Maytag 27
8
Maytag 27
9
Maytag 27
10
Maytag 27
11
Maytag 27
12
Maytag 27
13
Maytag 27
14
Maytag 27
15
Maytag 27
16
Maytag 27
17
Maytag 27
18
Maytag 27
19
Maytag 27
20
Maytag 27
21
Maytag 27
22
Maytag 27
23
Maytag 27
24
Maytag 27
25
Maytag 27
26
Maytag 27
27
Maytag 27
28
Maytag 27
29
Maytag 27
30
Maytag 27
31
Maytag 27
32
Maytag 27
33
Maytag 27
34
Maytag 27
35
Maytag 27
36
10
#
Slide 8
Press and hold 3 sec.
Quick Service Cycle
Quick Service Cycle
While in Service Mode, pressing the Temperature and Soil
Level key for 3seconds will start a Quick Service Cycle.
This will be a quick check of all systems. If display shows od
then open and close door. Pressing Spin Speed will advance
to the next cycle. The following steps are performed: Display
shows “SC”.
Refer to Technical Data Sheet for Detailed Instructions
Quick Service Cycle
While in Service Mode, pressing the Temperature and Soil Level key for
3seconds will start a Quick Service Cycle. This will be a quick check of all
systems. If display shows od then open and close door. Pressing Spin Speed will
advance to the next cycle. The following steps are performed: Display shows “SC”.
1. Hot water for 5 seconds and then turn off.
2. Cold water for 5 seconds and then turn off.
3. Bleach valve for 5 seconds and then turn off.
4. Dispenser softener using cold water and bleach water for 5 seconds and then turn off.
5. Turn on Cold valves until the control detects proper water level. During this time, tumble at
45 rpm for 5seconds in a clockwise direction, pause for 2seconds, tumble at 45 rpm for 5
seconds in a counterclockwise direction, pause for 2 seconds. Continue pattern until the
water level is detected. Minimum time for this segment to be 5 seconds. After water height is
achieved, continue tumble pattern for another 14 seconds. If the washer is equipped, turn on
heater for first 5 seconds of this tumble pattern. Advance the washer to next step if water is
not connected to machine.
6. Drain and spin to maximum speed. Machine will achieve maximum speed using the safest,
fastest method.
7. Display a “PA” (Passed) continuously for 5 seconds I no diagnostic codes were logged
during the test. Washer will return to the normal Service Mode at the end of the 10 second
period.
The “SC in the display will blink as an indication of failure, and continue blinking until the quick
service cycle test has reached the end. Any diagnostic code logged during this test will result in
failure of the test, but will not necessarily stop the test. During the Quick Service Cycle, pressing the
Spin Speed key will advance to the next step. Pressing the Rinse&Spin and Spin Only keys will
suspend the machine at the current step for up to 10 minutes or until Delay Start and Chime are
pressed again. All LEDs should flash on and off while the system is suspended or on hold.