Maytag 27" Troubleshooting Manual

Download Troubleshooting manual of Maytag 27" Washer for Free or View it Online on All-Guides.com.

Brand: Maytag

Category: Washer

Type: Troubleshooting manual for Maytag 27"

Pages: 36

Download Maytag 27" Troubleshooting manual

Maytag 27
1
Maytag 27
2
Maytag 27
3
Maytag 27
4
Maytag 27
5
Maytag 27
6
Maytag 27
7
Maytag 27
8
Maytag 27
9
Maytag 27
10
Maytag 27
11
Maytag 27
12
Maytag 27
13
Maytag 27
14
Maytag 27
15
Maytag 27
16
Maytag 27
17
Maytag 27
18
Maytag 27
19
Maytag 27
20
Maytag 27
21
Maytag 27
22
Maytag 27
23
Maytag 27
24
Maytag 27
25
Maytag 27
26
Maytag 27
27
Maytag 27
28
Maytag 27
29
Maytag 27
30
Maytag 27
31
Maytag 27
32
Maytag 27
33
Maytag 27
34
Maytag 27
35
Maytag 27
36
1
Slide 1Troubleshooting
Slide 2
Always refer to the Technical Data Sheet shipped with the product for detailed information
for the model you are servicing. Follow all Caution and Safety Warnings
The following is an example of the information available on the Technical Data Sheet
Will Not Start
Plug cord into live electrical outlet. Check for proper voltage.
Check fuse or reset circuit breaker.
Push any key to turn on the clothes washer. Push the rotary selector knob to start the washer.
Close door and push the rotary selector knob to start the clothes washer.
Check to see if the washer is in a pause or soak period in the cycle. Wait briefly for machine
to start. (If washer is in suds period, “SUDs” will display instead of remaining time.
Check for restricted drain system. During an electrical drain problem, “nd” error will occur
after 15 minutes.
Check water supply is working.
Check water valve connections are good.
Check the line filter and water valve filter.
Check the machine control board terminal connections CN5, CN6 for good connections.
Replace console control board.
Leaking
Make sure inlet hose connections are not leaking. Check for rubber gasket damage due to
over-tightening.
Check standpipe for leak. Wrap a dry rag around the standpipe opening. If rag becomes wet,
leak is fault of home plumbing. Be sure the standpipe is capable of accepting the flow of
water from the washer.
Make sure end of drain hose is correctly inserted and secured to drain standpipe.
Check internal hose connections (fill, drain systems, dispenser hoses & clamps).
Check rubber boot. Remove, reposition and reinstall, if necessary.
Check for possible kinked dispenser to outer tub hose. Hot water pressurization may force
door open.
No Tumble
Start normal cycle with an empty machine and allow a fill to check tumble.
Perform Board Output Test, or Quick Spin Test (Before test, make sure that the tumbler is
empty.)
Check for loose connections at Machine Control Board, Pressure Switch, Motor, Tach
Harness and Motor Control. (Refer to the component testing procedure)
Check motor windings resistance. (CN9 pins 1 &3 = 11.6ohms(±7% 20°C/68°F basis), pins 1
& 2 = 11.6ohms(±7%20°C/68°F basis), Pin2 & 3 = 11.6 ohms (±7% 20°C/68°Fbasis)
Check belt.
Faulty Main Control Board.
Faulty motor.