• Home
• Brands
• Banner Manuals
• Banner Plastic Fiber Optic PBT46UC
• Banner Plastic Fiber Optic PBT46UC Assembly Instruction

Banner Plastic Fiber Optic PBT46UC Assembly Instruction

Download Assembly instruction of Banner Plastic Fiber Optic PBT46UC Home Safety Product for Free or View it Online on All-Guides.com.

1

2

.04" diameter coiled bifurcated fiber with threaded sensing end

Plastic Fiber Optic Assembly model PBT46UC

PBT46UC p/n 26086

This Banner plastic fiber is designed to be cut by the customer to the length required for the application. To

facilitate cutting, a Banner model PFC-1 cutting device is supplied with this fiber. Cut the fiber as follows:

1) Locate the "control end" of the fiber (the unfinished end). Determine the length of fiber required for the

application. At the control end of the fiber, separate the two fibers. Lift the top (blade) of the cutter to

open the cutting ports. Insert one of the control ends through one of the four large cutting ports on the

PFC-1 cutter so that the excess fiber protrudes from the back of the cutter.

2) Double-check the fiber length, and close the cutter until the fiber is cut. Using a different cutting port, cut

the second control end to the same length as the first. Separate the cut ends for a length of 2 to 3 inches

to allow proper attachment to the sensor.

3) Gently wipe the cut ends of the fiber with a clean, dry cloth to remove any contamination.

Do not use solvents or abrasives on any exposed optical fiber. Do not use a cutting port more than once.

The blade may tend to dull after one cut.

SENSING RANGE: A function of the sensor. For further information, see the data

sheet packed with the sensor, or refer to the Banner product catalog.

TEMPERATURE EXTREMES: Temperatures below -30°C will cause embrittlement of

the plastic materials but will not cause transmission loss. Temperatures above +70°C

will cause both transmission loss and fiber shrinkage.

REPEAT BENDING/FLEXING: Life expectancy of plastic fiber optic cable is in excess

of one million cycles at bend radii of no less than the minimum (stated at right) and a

bend of 90 degrees or less. Avoid stress at the point where the cable enters the sen-

sor ("control end") and at the sensing end tip. Coiled plastic fiberoptic assemblies are

recommended for any application requiring reciprocating fiber motion.

OPERATING TEMPERATURE: -30 to +70°C (-20 to +158°F).

CHEMICAL RESISTANCE: The acrylic core of the monofilament optical fiber will be

damaged by contact with acids, strong bases (alkalis) and solvents. The polyethylene

jacket will protect the fiber from most chemical environments. However, materials may

migrate through the jacket with long term exposure. Samples of fiber optic material

are available from Banner for testing and evaluation.

MINIMUM BEND RADIUS OF PLASTIC FIBER: 1.0 inch (25 mm)

CONSTRUCTION:

OPTICAL FIBER: acrylic monofilament

PROTECTIVE JACKET: black polyethylene

THREADED END TIP and hardware: nickel plated brass

Fiber Cutting Information

Additional Specifications

Printed in USA p/n 03433L4B

Model PBT46UC is a bifurcated coiled plastic fiber optic assembly with

an M6 x 0,75mm threaded nickel plated brass sensing end. Coiled plastic

fibers are especially suited to applications requiring repeated flexing (re-

ciprocating motion).

The PBT46UC operates in the diffuse sensing mode. Sensing light is

transmitted and received through the threaded fiber sensing end. Objects

are detected by the light they reflect back through the sensing end. Fiber

core diameter is .04 inch.

The PBT46UC may be used with plastic fiber optic sensors from the following Banner sensor families: D12, OMNI-BEAM, MAXI-

BEAM, VALU-BEAM, Q45, PC44, MINI-BEAM, and ECONO-BEAM. See page 2 for further information.

Description

PFC-2 Cutting Device