NAPCO GEM-RS232 Installation Instructions

Download Installation instructions of NAPCO GEM-RS232 Computer Hardware, Security System for Free or View it Online on All-Guides.com.

Brand: NAPCO

Category: Computer Hardware , Security System

Type: Installation instructions for NAPCO GEM-RS232

Pages: 2

Download NAPCO GEM-RS232 Installation instructions

NAPCO GEM-RS232 Installation instructions - Page 1
1
NAPCO GEM-RS232 Installation instructions - Page 2
2
1
GEM-RS232
Control Panel / Computer Converter
INSTALLATION INSTRUCTIONS
R
333 Bayview Avenue
Amityville, New York 11701
For Sales and Repairs, (800) 645-9445
For Technical Service, (800) 645-9440
© Napco 1999 WI966 6/99
GENERAL DESCRIPTION
The GEM-RS232 Control Panel/ Computer Converter is
an interface module which allows the NAPCO GEM-P9600
control panel to be connected to a computer which may be
used to display system status. The GEM-RS232 is
approved by Underwriters Laboratories for supplemental
use only. It provides signal and ground isolation between
the control panel and the computer and will protect the
control panel from shorts, transients and surges which may
emanate from the computer or the associated cabling.
The GEM-RS232 has been designed to be permanently
mounted inside the cabinet of the GEM-P9600 and can be
connected to the computer in several different fashions
(see CONNECTION).
SPECIFICATIONS
Input Power: 12 V DC nominal, 60 mA (supplied by control
panel connections)
Note: Reduce available panel combined auxiliary current
by 60 mA)
Dimensions: 11/16” x 2 9/16” x 2 9/16” (HxWxD)
Range: 50 feet using RS232 serial cable
100 feet using Cat5 cable
ORDERING INFORMATION
1. GEM-RS232
RS232 Converter
6 conductor Modular to Modular (RJ12 Style) cable
1 SE-AUTOMATION EPROM
2. GEM-RS232KIT
RS232 Converter
6 conductor Modular to Modular (RJ12 Style) cable
8 Pin Modulator (RJ45 Style) to DB9 Male Adapter
8 Pin Modulator (RJ45 Style) to DB9 Female
Adapter
1 SE-AUTOMATION EPROM
SYSTEM REQUIREMENTS
The following system hardware is required:
Gemini GEM-P9600 Control Panel
SE-AUTOMATION EPROM Upgrade must be
installed in control panel.
MOUNTING INSTRUCTIONS
1 Open GEM-RS232 case using screwdriver.
2 Drill hole in the center of the base of the case
(side without label) using a 1/8” drill bit.
3 Drill hole in housing using a 1/8” drill bit
4 Mount securely using nut and screw provided
CONNECTION
Refer to the wiring diagram. Connect the 6-conductor
modular cable (supplied) to J1 (RJ12 style) of the
control panel and then plug into the module (RJ12
style) plug on the RS232 converter.
For direct connection to serial port of computer or
automation system, plug male DB9 connector of
serial cable (NOT supplied) into the DB9 connector
of the RS232 converter and connect other end to
serial port of computer.
For CAT 5 wiring to computer or automation system,
plug male DB9/CAT5 connector (supplied with
GEM-RS232KIT) into the DB9 connector of the
RS232 adapter and connect female DB9/CAT5
connector (supplied with GEM-RS232KIT) to
automation system DB9 connector. Use CAT5
cable terminated with standard RJ45 connectors
(not supplied).
NAPCO Security Systems, Inc.
333 Bayview Avenue, Amityville, New York 11701
For Sales and Repairs, call toll free: (800) 645-9445
For direct line to Technical Service, call toll free: (800) 645-9440
Internet: http://www.napcosecurity.com