Edge Products CS Quick Install Manual

Download Quick install manual of Edge Products CS Automobile Accessories, Automobile Electronics for Free or View it Online on All-Guides.com.

Edge Products CS Quick install manual - Page 1
1
Edge Products CS Quick install manual - Page 2
2
Supplied Items Suggested Tools
CS or CTS Device1.
Arkon Windshield Mount2.
OBDII Cable3.
Mini USB Cable4.
CD5.
Alcohol Wipe6.
Zip Tie Packet7.
Flat head screwdriver•
1
2
3
4
5
6
7
The OBDII port is a 16-pin connector like the illustration be-
low.
The OBDII port is located un-
der the dash below
the steering wheel.
The OBDII port is
placed in dierent
locations under the
dash for dierent
applications; refer to
the OBDII port loca-
tion drawing (left) to
help you locate your
OBDII port.
*07 + Ford Superduty OBDII
port is located on the left side
of the wheel instead of the right.
* 94-97 Ford Powerstroke OBDII port
is located on the passenger side below
and to the left of the glove box.
FORD
DODGE
GM-CHEV
Once you’ve removed
the necessary panels,
connect the OBDII
cable to the OBDII
port, and route the
cable under the dash,
out the side panel, up be-
tween the door seal trim
and the edge of the dash.
Tuck the cable back as far
as you can as you route it
up to the dash.
Remove the panel on the
side of the dashboard to
provide access to route
the OBDII cable from the
OBDII port up to the top
of the dash.
*On some vehicles you may also
need to remove the panel directly
under the steering wheel.
*Note: Leave 6-10”
of cable exposed on
top of the dash so you
have room to posi-
tion the device.
OBDII PORT
Position the device
and the mount on
the windshield in the
desired location.
Pay attention to
where the suction
cup will mount on the
windshield.
Once you’ve identied
the suction cup position
on the windshield, use
the supplied alcohol wipe
to thoroughly clean the
area. After you’ve wiped
the area clean, let it dry
for 2-3 minutes.
Before you attach the suc-
tion cup portion of the
mount to the window
attach it to the device.
Insert the tabs on the
mount into the slots on
the back of the device and
slide up (CTS) or to
the side (CS) until it
stops.
*The mounting tabs are a tight
t by design to maintain
a solid connection.
Next, insert the connector on the end
of the OBDII cable into the 16-pin
connector on the back of the device
(this is easier if done prior to mount-
ing the device on the window). The
connector only ts one way so be
sure that the locking tab is on the
bottom.
Note: The device will power on
automatically when it detects your
vehicle has started. If you wish to
power up the device without starting
your vehicle, ensure the key is in the
run position and touch the screen
(CTS) or a button (CS).
Once the alcohol has dried
you’re ready to attach the
mount to the wind-
shield.
UNLOCKED
Once you’ve locked the mount to
the windshield, use the adjustment
knobs to ne tune the viewing angle
and height of the the CTS/CS device.
CS/CTS QUICK INSTALL INSTRUCTIONS
Step 1: Locate the OBDII Port
Step 2: Connect/Route the OBDII Cable Step 3: Position the Device
Step 4: Connect the Mount and OBDII Cable
Step 5: Position and Lock the Device on theWindshield
VERTICAL ADJ.
KNOB
This knob will allow you
to adjust the viewing
angle and height of the
device up or down.
LOCKED
You’ll notice that the mount has
a locking tab. This tab creates the
suction that will lock the mount
to the windshield. Make sure
the lock is in the “Unlocked”
position. Position the
mount where you’ve
cleaned the windshield,
press rmly, and push the tab to the
“Locked” position.
VARIABLE ANGLE ADJ
KNOB
This knob will allow you to
adjust the viewing angle of
the device in both horizontal
and vertical fashions. Use
it to ne tune your viewing
angle.
OBDII LOCATIONS