Home | About | Contact

Acoustic Research AWSBT7 Installation And Operation Manual

Download Installation and operation manual of Acoustic Research AS7WH Speakers for Free or View it Online on All-Guides.com.

Acoustic Research AS7WH Installation and operation manual - Page 1
1
Acoustic Research AS7WH Installation and operation manual - Page 2
2
Acoustic Research AS7WH Installation and operation manual - Page 3
3
Acoustic Research AS7WH Installation and operation manual - Page 4
4
Acoustic Research AS7WH Installation and operation manual - Page 5
5
Acoustic Research AS7WH Installation and operation manual - Page 6
6
Page 1
background image

Powering the Speaker

There are two options to power your wireless speaker: using the included AC power adapter 
or using 6 AA batteries (not included). 

AC Power Adapter

1.   Insert the small, round plug from the speaker AC 

power adapter into the DC IN jack on the bottom 
panel of the speaker.

2.  Plug the other end of the speaker AC power 

adapter into any standard 120V AC wall outlet. 

Notes:

 Be sure to use the speaker AC power adapter 

rated 10V DC 1500 mA. 

The power unit should be plugged in so that it stays 
vertical or lies fl at.

AA Batteries

1.   Remove the battery compartment cover on the bottom of the speaker.

2.  Insert six (6) AA batteries (not included) into the speaker following the polarity 

 

(”+” and “-”) as diagrammed inside the battery compartment.

3.  Replace the battery compartment cover on the bottom of the speaker.

Note:

 Place the rubber cap in the speaker power input jack when using batteries.

DO NOT

 mix batteries with different chemistry types (for example, a zinc battery with an alkaline 

battery). 

DO NOT

 mix new and used batteries. 

DO NOT 

leave batteries installed in the product 

when not in use for long periods. Always remove old, weak or worn-out batteries promptly and 
recycle or dispose of them in accordance with local and national regulations.

Introduction

The Acoustic Research AWSBT7 portable wireless speaker makes it easy to take your music 
wherever you go and share it whenever you want, with  Bluetooth® wireless connectivity and 
an built-in auxiliary input. It’s compact, easy-to-carry and simple to use, with a UV and water-
resistant exterior that lets you take it to the beach, tailgating, the basketball court, even on a 
camping trip, with no worries. 

This speaker even offers a protected storage space for your wallet, keys, etc., even for your 
MP3 player while it’s connected wirelessly to the speaker. So you can relax and enjoy.

This manual covers various connection options and detailed operating instructions for 
making the Acoustic Research Portable Wireless Speaker a valued part of your lifestyle. If, 
after having reviewed the instructions, you have any questions, please call 

 

  

toll-free 1-800-732-6866 or visit www.acoustic-research.com.

Important Information

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

CAUTION

Caution:

 To reduce the risk of electric shock, do not remove cover (or back). No 

user serviceable parts inside. Refer servicing to qualifi ed service personnel.

Product Information

Keep your sales receipt to obtain warranty parts and service and for proof of purchase. Attach it here and record the 
serial and model numbers in case you need them. These num bers are located on the product. 
Model No.: _____________________________________________________________________________________________
Purchase Date: _________________________________________________________________________________________  
Dealer/Address/Phone: __________________________________________________________________________________

Important Safety Instructions

1.   Read these instructions.
2.  Keep these instructions.
3.  Heed all warnings.
4.  Follow all instructions.
5.  Clean only with dry cloth.
6.  Do not block any ventilation openings. Install in 

accordance with the manufacturer’s instructions.

7.   Do not install near any heat sources such as radiators, 

heat registers, stoves, or other apparatus (including 
amplifi ers) that produce heat.

8.  Protect the power cord from being walked on or pinched 

particularly at plugs, con ve nience re cep ta cles, and the 
point where they exit from the apparatus.

9.  Unplug this apparatus during lightning storms or when 

unused for long periods of time.

10. Refer all servicing to qualifi ed service personnel. 

Servicing is required when the apparatus has been 
dam aged in any way, such as power-supply cord or plug 
is damaged, liquid has been spilled or objects have fallen 
into the apparatus, the ap pa ra tus has been exposed to 
rain or moisture, does not op er ate normally, or has been 
dropped.

Care and Maintenance

• Always use a soft cloth to clean the speaker and transmitter. Never use any product containing alcohol or other 

solvents as they may damage the surface.

• Use caution when plugging the power transformers in an AC outlet to avoid the risk of electric shock.
• If the speaker are used outside on a deck or patio, make sure you take them indoors in the event of a rainstorm to 

prevent possible damage.

• Do not operate or store the system in extreme temperatures (below 32ºF/0ºC and above 122ºF/50ºC).

Tour of the Speaker

Powering the Speaker System

Model

 AWSBT7

Installation and Operation Manual

Portable   

 

 

Wireless 
Speaker

Setting Up Bluetooth Wireless

Pairing

The Bluetooth-enabled device that you wish to stream audio to your speaker system must 
fi rst be paired to the speaker.  The process is simple, and in most cases the pairing process 
needs to be done only once.

To pair your Bluetooth-enabled device with the speaker:

1.   Make sure your device’s Bluetooth is turned on. See the wireless and/or network settings 

menu on your device to check.

2.  If the speaker isn’t already on, press the On-Off button to turn it on. You will hear a beep 

to indicate the speaker is turned on. The indicator light on the back of the speaker starts 
fl ashing blue.

3.  Press and hold for 3 seconds the Pair button to enter pairing mode. You will hear 2 beeps 

to indicate pairing mode is entered. The indicator on the back of the speaker starts blinking 
faster. 

4. Open the Bluetooth settings menu on your device. Select “AR SPEAKER” from the list of 

devices available (you might have to scan for devices). If your device asks for a password, 
enter “0000”.

5.  A confi rmation screen will appear on your device once the speaker and the device are 

successfully paired. The blue indicator turns solid blue to indicate successful connection. 
The speaker is now ready for you to stream audio from your device.

6. Turn the volume on your device to at least 3/4 max, then start playing something on the 

device. Control the speaker volume on the speaker itself, using the Volume +/– buttons on 
the back of the speaker.

Note: 

•  

If you notice the sound from the speaker is distorted, turn down your device’s volume.

For PLUGGABLE EQUIPMENT, the socket-outlet shall 

be installed near the equipment and shall be easily 
accessible.

The apparatus shall not be exposed to dripping or 

splashing or placed near objects fi lled with liquids.

Back panel 

Power and Pairing indicator 

shows the 

status of the speaker. 

Blue, slow blinking: The speaker is on but not 
paired or connected (like when you turn the 
speaker on for the first time).

Blue, fast blinking: The speaker is in Bluetooth 
pairing mode. See the Bluetooth Setup section 
for more information.

Solid blue: The speaker is paired with a 
Bluetooth-enabled device and ready to play 
audio.

On-Off 

button turns the speaker on and off.

Pair-Press and hold (3 sec) 

puts the 

speaker in pairing mode for Bluetooth setup 
(press and hold for 3 seconds). It also performs 
a fast reconnect with devices that have lost 
connection (press). See the Bluetooth setup 
section for more information.

Volume +/–

 buttons adjust the speaker’s 

volume level.

Audio Input 

connects directly to your 

MP3 player, smartphone, or other portable 
audio device, using the 3.5mm audio in cable 
provided.

Bottom panel 

DC IN 

receives the small round end of the 

included 10V 1500mA AC power adapter; 
remove the protective cover to insert the 
adapter.

Battery Compartment Cover

   

 

remove to install 6 AA batteries.