Billy Goat FM3300IN, FM3300INE Operator Owner's Manual

Download Operator owner's manual of Billy Goat FM3300IN, FM3300INE Lawn Mower for Free or View it Online on All-Guides.com.

Billy Goat FM3300IN, FM3300INE Operator owner's manual - Page 1
1
Billy Goat FM3300IN, FM3300INE Operator owner's manual - Page 2
2
Billy Goat FM3300IN, FM3300INE Operator owner's manual - Page 3
3
Billy Goat FM3300IN, FM3300INE Operator owner's manual - Page 4
4
Billy Goat FM3300IN, FM3300INE Operator owner's manual - Page 5
5
Billy Goat FM3300IN, FM3300INE Operator owner's manual - Page 6
6
Billy Goat FM3300IN, FM3300INE Operator owner's manual - Page 7
7
Billy Goat FM3300IN, FM3300INE Operator owner's manual - Page 8
8
Billy Goat FM3300IN, FM3300INE Operator owner's manual - Page 9
9
Billy Goat FM3300IN, FM3300INE Operator owner's manual - Page 10
10
Billy Goat FM3300IN, FM3300INE Operator owner's manual - Page 11
11
Billy Goat FM3300IN, FM3300INE Operator owner's manual - Page 12
12
Billy Goat FM3300IN, FM3300INE Operator owner's manual - Page 13
13
Billy Goat FM3300IN, FM3300INE Operator owner's manual - Page 14
14
Billy Goat FM3300IN, FM3300INE Operator owner's manual - Page 15
15
Billy Goat FM3300IN, FM3300INE Operator owner's manual - Page 16
16
Billy Goat FM3300IN, FM3300INE Operator owner's manual - Page 17
17
Billy Goat FM3300IN, FM3300INE Operator owner's manual - Page 18
18
Billy Goat FM3300IN, FM3300INE Operator owner's manual - Page 19
19
Billy Goat FM3300IN, FM3300INE Operator owner's manual - Page 20
20
Billy Goat FM3300IN, FM3300INE Operator owner's manual - Page 21
21
Part No. 520166 Form No. F112003A
OPERATION continued
16
Page 8 of 20
Figure 16-2
Figure 16-1
16.3
CUTTING HEIGHT ADJUSTMENT
Cutting height can be adjusted from 1.0" to 3.5" by placing
spacers above or below caster spindles. For easiest adjust-
ment change the height on one side at a time. To change
cutting height, tilt the unit back, remove lynch pin, remove
all spacers then set if off to the side, remove caster rig, add
or subtract spacers, reinstall caster rig, place remainder
of spacers if any, then reinsert lynch pin (see gure 16-1
through 16-4). Repeat this step on other side.
NOTE: Be sure that the spacers are even on both casters.
Running the deck out of level will result in poor cut quality
and increased belt wear.
CAUTION: DO NOT make cutting height
adjustment when engine is running.
LOWEST
CUTTING
HEIGHT
OF 1.0"
HIGHEST
CUTTING
HEIGHT
OF 3.5"
spacers
lynch pin
caster
rig
Figure 16-3
Figure 16-4
16.4
BLADE CLUTCH
The FM mower blade clutch is controlled by an opera-
tor presence control. To engage the blade, depress
the operators left hand control lever against operators
handle. The blade is disengaged by releasing this
lever.(see gure 16-5)
NOTE: The blade clutch must be either fully engaged
for cutting or fully disengaged to bring the blade to
a stop. Do not operate the unit with the blade clutch
partially engaged. Premature belt wear and clutch
failure will result from improper operation of the clutch.
CAUTION: Use extreme care when operating the
blade. Inspect the work area for foreign objects that
could cause damage to the unit or injure the operator
if struck by the blade. Never operate the blade with
bystanders in the work area. Lever operate the blade
without either the discharge de ector chute or the grass
catcher in place.
Fig. 2
Figure 16-5
Blade Clutch-
Lever
Operator's
handle