• Home
• Brands
• Kenmore Manuals
• Kenmore 911.99002
• KENMORE ELITE 911.99002 Technical Data Sheet

KENMORE ELITE 911.99002 Technical Data Sheet

Download Technical data sheet of Kenmore 911.99002 Cooktop for Free or View it Online on All-Guides.com. This version of Kenmore 911.99002 Manual compatible with such list of devices, as: 911.99002, 911.99003, 911.99004, 911.99009

1

2

to damage terminals in block)-Should read 1100Ω at room ambient (approx.72°F).

• Measure each sensor lead from connector block to ground. If shorted, look for pinched or cut wire in sensor

circuit.

• Check connector terminals- Look for deformed or corrosion on terminals. Repair or replace.

• Check connector at sensor (remove sensor and carefully pull leads with connector into oven).

• If all above is ok, replace control.

• T E C H N I C A L D A T A S H E E T •

To Replace:

1. Place the drawer rail on the guides.

2. Push the drawer in until it stops.

3. Lift the front of the drawer and push in until the stops clear the guides.

4. Lower the front of the drawer and push in until it closes.

——— If Drawer is Crooked ———

——— If Drawer Won’t Close ———

STORAGE DRAWER REMOVAL

To Remove:

1. Pull the drawer out until it stops.

2. Lift the front of the drawer until the stops clear the guides.

3. Remove the drawer.

5. Remove the light bulb by unplugging it from both sockets with one motion.

To Install New Bulb:

1. Install the new light bulb by plugging it into

both sockets with one motion.

2. Using the hand grips on the cooktop light

housing, lift up and push the housing back into

the rear wall of the range. Then lower the

housing until the bottom tabs are inserted back

into the range.

3. Reattach the screws along the top edge on the back of the range.

Then push the range back against the wall.

Kenmore ELITE Radiant Free-Standing

Part Description Repair Part Number

6" Haliant Element WB30K5033

Bridge Element WB30T10088

9"Haliant Element WB30T10035

6"Haliant Element (Warmer) WB30T10042

Infinite Switch (Warmer) WB24T10012

Infinite Switch (Dual) WB24T10015

Infinite Switch-2600W WB24T10032

Infinite Switch-1500W WB24T10028

Oven Control WB27T10137

Oven Control-Stainless WB27T10144

Sensor WB23T10002

Glass Panel Asm-Black WB27T10160

NOTE:

• BAKE/TIME BAKE — Bake and broil units cycle during

preheat and balance of operation, one unit is on at a time.

• CLEAN — Broil unit only on

during 1st 30 minutes or

until oven reaches 750°F.

During balance of clean

oven will cycle between

bake and broil units.

Convection fan running make the following checks:

• Check the voltage from terminal CF to N on control - should read

120V in convection bake or roast mode.

• If voltage is OK, check convection fan motor. It reads approximately 15-20Ω’s at room

temperature. Check to make sure fan shaft is not rubbing on oven liner.

ERC FAILURE CODES

CODE

F0

Any key (other than Start of Clear/OFF pad)

shorted (after approx. 40 secs).

If code cannot be cancelled, unplug keypad and

power up. If 0) ceases, replace keypad/ glass

asm., If 0) is still present, replace main control.

F2

Over-temperature-915°F if lock circuit is

made, 615°F otherwise.

• Look for welded relay contacts. (Heating elements on

in off mode.)

If code cannot be cancelled, replace control.

If code cannot be cancelled, unplug keypad and

power up. If code ceases, replace keypad/glass

asm. If code is still present, replace main control.

F1

F7

F6

• Look for high resistance in the sensor circuit due to high contact resistance (poor terminal crimp, deformed

terminals, loose connection inside sensor tube) or intermittent solder joint.

• Electrical noise interference in the sensor circuit ( Ham radio, cordless phone, etc.)

F3

Sensor circuits open (2900 Ohms or greater).

F4

Sensor circuits shorted (950 Ohms or less).

• Disconnect power to range.

• Disconnect sensor connector at control. Measure

sensor resistance at control connector (take care not

F9

FC

Both lock and unlock circuits are activated at

the same time (after approx. 60 secs.)

Check wiring and test operation of switches.

Perform resistance check.

FF

Loss of door motor redundant driver protection.

Replace control

FA

Surface warmer on indicator light supervisor

error

Replace control

FE

NOTE: Connections can be intermittent due to a corrosive buildup between the connection to the terminals, or

by being bent by the insertion of a probe, etc.

MEANING

CORRECTION

229C4059P244

MOTORIZED DOOR LOCK

The motorized door lock assembly is located above the oven. The

assembly consists of a lock motor cam and switch assembly, lock

hook, heat barrier, and mounting plate.

Motorized Door Lock Operation:

The lock motor is energized when the control is set for Clean

and Clean Time selected. The K1 relay contact will close and

complete the circuit that supplies the voltage to the lock motor.

NOTE: Display of Control will flash “LOCK DOOR” if the door switch is in the “C” to “NC” position.

(Door open)

• The word “LOCKED DOOR” will flash on and off in the display while the

lock motor is in motion. When the door is locked the word “LOCKED

DOOR” remains illuminated in the display.

• CAM - The cam on the motor performs two functions:

1. Positions the lock hook in the door to prevent opening during clean

operation.

2. Operates the lock switches which tell the control if the door is unlocked or

locked and ready for clean operation.

NOTE: When door is either being locked or unlocked both lock switches will

be in the open position.

REPLACING THE COOKTOP LIGHT BULB

CAUTION: Disconnect electrical power to the range at the main circuit

breaker or fuse box before attempting to replace the cooktop light bulb. Do

not touch a hot light bulb with wet hands or a wet cloth. Wait until the bulb

has cooled and use a dry cloth.

To Remove Old Bulb:

1. Pull the range away from the wall.

2. Remove the two screws from the top on the

back of the range.

3. Pull up on the hand grips on the back of the range

until the tabs at the bottom of the cooktop light

housing separate from the back of the range.

4. Pull out the cooktop light housing as far as possible, about 2 inches.

Part Description Repair Part Number

Glass Panel Asm-White WB27T10155

Glass Panel Asm-Bisque WB27T10159

Glass Panel Asm-GPH/ SS WB27T10157

Glass MT ASM-Black WB62T10040

Glass MT ASM-Bisque WB62T10039

Glass MT ASM-White WB62T10038

Glass MT ASM-GPH WB62T10037

Bake Element -Hidden WB44T10015

Convection Element WB44T10001

Broil Element WB44T10008

Halogen Lamp WB08T10007

Clear/Off pad is shorted or touch board fault

(after approx. 100 secs).

Loss of element redundant driver protection.