Home | About | Contact

Maytag RFS9B Service

Download Service of Maytag 1324704M Microwave Oven for Free or View it Online on All-Guides.com. This version of Maytag 1324704M Manual compatible with such list of devices, as: P1324001M, P1324706M, P1327708M, P1327709M, P1327711M

Maytag 1324704M Service - Page 1
1
Maytag 1324704M Service - Page 2
2
Maytag 1324704M Service - Page 3
3
Maytag 1324704M Service - Page 4
4
Maytag 1324704M Service - Page 5
5
Maytag 1324704M Service - Page 6
6
Maytag 1324704M Service - Page 7
7
Maytag 1324704M Service - Page 8
8
Maytag 1324704M Service - Page 9
9
Maytag 1324704M Service - Page 10
10
Maytag 1324704M Service - Page 11
11
Maytag 1324704M Service - Page 12
12
Maytag 1324704M Service - Page 13
13
Maytag 1324704M Service - Page 14
14
Maytag 1324704M Service - Page 15
15
Maytag 1324704M Service - Page 16
16
Maytag 1324704M Service - Page 17
17
Maytag 1324704M Service - Page 18
18
Maytag 1324704M Service - Page 19
19
Maytag 1324704M Service - Page 20
20
Maytag 1324704M Service - Page 21
21
Maytag 1324704M Service - Page 22
22
Maytag 1324704M Service - Page 23
23
Maytag 1324704M Service - Page 24
24
Maytag 1324704M Service - Page 25
25
Maytag 1324704M Service - Page 26
26
Maytag 1324704M Service - Page 27
27
Maytag 1324704M Service - Page 28
28
Maytag 1324704M Service - Page 29
29
Maytag 1324704M Service - Page 30
30
Maytag 1324704M Service - Page 31
31
Maytag 1324704M Service - Page 32
32
Maytag 1324704M Service - Page 33
33
Maytag 1324704M Service - Page 34
34
Maytag 1324704M Service - Page 35
35
Maytag 1324704M Service - Page 36
36
Maytag 1324704M Service - Page 37
37
Maytag 1324704M Service - Page 38
38
Maytag 1324704M Service - Page 39
39
Maytag 1324704M Service - Page 40
40
Maytag 1324704M Service - Page 41
41
Maytag 1324704M Service - Page 42
42
Radiation Leakage Testing
!
WARNING
To avoid risk of electrical shock, personal injury, or death, disconnect power to oven and discharge capacitor
before servicing, unless testing requires it.
16021520 Rev. 0
©2002 Maytag Appliances Company16
WARNING
!
Check for radiation leakage after servicing. Should the
leakage be more than 4 mW/cm
2
inform Maytag
immediately. After repairing or replacing any radiation
safety device, keep a written record for future reference,
as required by D.H.H.S. and HEW regulations. This
requirement must be strictly observed. In addition, the
leakage reading must be recorded on the service repair
ticket while in the customer’s home.
Equipment
Electromagnetic radiation monitor
600 cc glass beaker
Procedure for Measuring Radiation Leakage
Note before measuring:
Do not exceed meter full scale deflection. Leak monitor
should initially be set to the highest scale.
To prevent false readings the test probe should be held
by the grip portion of the handle only.
The scan speed is equal to one inch per antenna
revolution or one inch per second if antenna speed is
unknown.
Areas to be checked are all door seal areas and any
venting parts.
Leakage with the outer panel removed ...4mW/cm
2
or
less.
Leakage for fully assembled oven with door normally
closed ...4 mW/cm
2
or less.
Leakage for a fully assembly oven (before the latch
switch (primary) is interrupted) while pulling the door
... 4 mW/cm
2
or less.
1. Pour 275 cc ±15 cc (9 oz ±1/2 oz) of 20°C ± 5°C
(68°F ± 9°F) water in a beaker which is graduated to
600 cc and place the beaker in the center of oven.
2. Set the radiation monitor to 2450 MHz and use it
following the manufacturer’s recommended test
procedure to assure correct results.
3. While measuring the leakage, always use the two inch
(5 cm) spacer supplied with the probe.
4. Press the start pad or turn on the timer and with the
magnetron oscillating, measure the leakage by holding
the probe perpendicular to the surface being
measured.
Measurement with the Outer Panel
Removed
WARNING
!
Avoid contacting any high voltage components.
Whenever you replace the magnetron, measure for
radiation leakage before the outer panel is installed
and after all necessary components are replaced or
adjusted. Special care should be taken in measuring
around the magnetron.
Measurement with a Fully Assembled
Oven
After all components including the outer panel are fully
assembled, measure for radiation leakage around the
door periphery, the door viewing window, the exhaust
opening, and air inlet openings.
Record Keeping and Notification After
Measurement
1. After any adjustment or repair to a microwave
oven, a leakage reading must be taken. Record
this leakage reading on the repair ticket even if it is
zero.
2. A copy of the repair ticket and the microwave
leakage reading should be kept by the repair
facility.