KING CB SERIES Installation Manual

Download Installation manual of KING CB SERIES Heater for Free or View it Online on All-Guides.com.

Brand: KING

Category: Heater

Type: Installation manual for KING CB SERIES

Pages: 4

Download KING CB SERIES Installation manual

KING CB SERIES Installation manual - Page 1
1
KING CB SERIES Installation manual - Page 2
2
KING CB SERIES Installation manual - Page 3
3
KING CB SERIES Installation manual - Page 4
4
KING ELECTRICAL MFG. CO. · 9131 10TH AVENUE SOUTH · SEATTLE, WA 98108 · TEL: 206.762.0400 · FAX: 206.763.7738
CB SERIES
BASEBOARD HEATER
INSTALLATION GUIDE
ATTENTION: Before attempting to install your heater, verify that the power
supply wires are the same voltage as the heater you are installing. The best
way to check for proper voltage is by using a voltmeter, testing between
supply line 1 and 2. 240 and 120 Volt heaters are not interchangeable.
Connecting a 240 Volt heater to a 120 Volt circuit will reduce the wattage
75% making the heater feel barely warm. Connecting a 120 Volt heater to
a 240 Volt circuit will destroy the heater, could cause re damage, personal
injury or death, and, voids all warranties.
WARNING: Turn off power source to the heater before attempting instal-
lation, maintenance or repairs. Lock, tape or tag circuit breaker or fuse so
that power cannot be turned on by accident. Failure to do so could result in
serious electrical shock, burns or possible death.
PLACEMENT: When possible baseboard heaters should be placed on an
outside perimeter wall under a window. This is due to the fact that the out-
side wall is usually the spot of greatest heat loss. A baseboard heater may
sit directly on any oor surface including carpet. Do not allow carpet to block
air intake at bottom.
GENERAL SAFETY INFORMATION: Keep electrical cords, any bulky fur-
niture or other household items that could restrict air ow away from heater.
Refer to clearance diagram for drapes. Do not install heater below an electri-
cal outlet or against vinyl wallpaper, paperboard or low density berboard
surfaces. Do not recess mount heater. Do not mount heater vertically. Do not
store ammable liquids in vicinity of the heater. Installation must comply with
applicable national and local electrical codes. Protect electrical supply wire
from nicks, sharp objects, oil, grease or other chemicals that could damage
the insulation.
INSTALLATION INSTRUCTIONS:
1. Make sure heater is positioned on the wall with the “Bottom” label facing
the oor. Mounting upside down could be a hazard.
2. Remove junction box cover from left or right end. The heater can be
wired from either end.
3. Remove knockout and pull supply wires through. Use a cable tting to
secure the power wires.
4. Locate wall studs and secure heater to wall with a nail or screw. Use the
mounting dimples in the back can to position the fastener. The dimples
will prevent the fastener from slipping when applying pressure to pierce
the metal back can. You do not have to remove the cover or re ector to
mount the heater.
5. Connect electrical wires and groundwire to the heater per the appropri-
ate wiring diagram on following pages.
1½" between drapes
and ceiling
1½"
4"
1½" above carpet
CEILING
WALL
FLOOR
CLEARANCE MINIMUMS FOR DRAPES
CIRCUIT SIZING TABLE
1,440
AMPS VOLTS WATTS WIRE SIZE
CIRCUIT PROTECTION
15 Amp - 1 Pole
#14/2
120
12
16
12
16
24
120
240
240
240
1,920
2,880
3,840
5,700
#14/2
#12/2
#12/2
#10/2
20 Amp - 1 Pole
15 Amp - 2 Pole
20 Amp - 2 Pole
30 Amp - 2 Pole
CB.indd : 2/09
16" to 24"
from furniture