Control4 C4-SW120277 Installation Manual

Download Installation manual of Control4 C4-SW120277 Switch for Free or View it Online on All-Guides.com.

Brand: Control4

Category: Switch

Type: Installation manual for Control4 C4-SW120277

Pages: 4

Download Control4 C4-SW120277 Installation manual

Control4 C4-SW120277 Installation manual - Page 1
1
Control4 C4-SW120277 Installation manual - Page 2
2
Control4 C4-SW120277 Installation manual - Page 3
3
Control4 C4-SW120277 Installation manual - Page 4
4
Warnings and Considerations
WARNING! Turn OFF electrical power before installing or servicing this
product. Improper use or installation can cause SERIOUS INJURY, DEATH
or LOSS/DAMAGE OF PROPERTY.
ATTENTION! Coupez l’alimentation électrique avant d’installer ou de
réparer ce produit. Une mauvaise installation ou utilisation peut entraîner
des blessures graves, décès ou perte / dommages à la propriété.
WARNING! This device must be protected by a circuit breaker (20A max).
ATTENTION! Cet appareil doit être protégé par un disjoncteur (20A max.)
WARNING! Ground this device in accordance with the National Electric
Code (NEC) requirements. DO NOT rely solely upon the yoke plate’s
contact with a metal back box for adequate grounding. Use the device’s
ground wire to make a secure connection to the safety ground of the
electrical system.
ATTENTION! Cet appareil doit être en conformité avec le Code national
de l’électricité (NEC). Ne comptez pas uniquement au contact de la
plaque avant avec un boîtier mural métallique pour la mise à la terre
adéquate. Utilisez cet appareil à la terre de l’appareil pour établir une
connexion sécurisée au système électrique.
IMPORTANT! This device must be installed by a licensed electrician in
accordance with all national and local electrical codes.
IMPORTANT! If you are unsure about any part of these instructions,
consult a qualified electrician.
IMPORTANT! Use this device only with copper or copper-clad wire. Do
not use aluminum wiring. This product has not been approved for use with
aluminum wiring.
IMPORTANT! Using this product in a manner other than outlined in this
document voids your warranty. Further, Control4 is NOT liable for any
damage incurred with the misuse of this product. See “Troubleshooting.”
IMPORTANT! Do NOT use a power screwdriver to install this device. If you
do, you may overtighten the screws and strip them. Also, overtightening
the screws may interfere with proper button operation.
IMPORTANT! This is an electronic device with intricate components.
Handle and install with care!
Installation Instructions
1 Ensure that the location and intended use meet the following criteria:
đŏ Do not exceed the load capacity requirements of the switch. Refer to the load
ratings in the specifications above for details.
đŏ Install in accordance with all national and local electrical codes.
đŏ The range and performance of the wireless control system is highly
dependent on the following: (1) distance between devices; (2) layout of the
home; (3) walls separating devices; and (4) electrical equipment located near
devices.
2 Turn o the local electrical power by either switching o the circuit breaker or
removing the fuse from the fuse box. To ensure the wires do NOT have power
running to them, use an inductive voltage detector.
NOTE: The back box wiring shown in this document is an example. Your
wire colors and functions may dier. If you are not sure which wires
are the Hot, Neutral, Load, Traveler, and Ground wires, have a trained
electrician perform the installation.
3 Prepare each wire. Wire insulation should be stripped back 5/8 of an inch
from the wire end (see Figure 1).
Supported Model
đŏ C4-SW120277 Switch
Introduction
The Control4® Switch operates independently or as part of a Control4 home
automation system. It installs in a standard back box using typical wiring standards
and communicates to the Control4 system using a wireless connection.
Box Contents
đŏ Switch
đŏ Wire Nuts
đŏ Warranty Card
đŏ
3%0$ŏ*/0((0%+*ŏ1% ! (this document)
Specifications and Supported Load Types
The specifications are described below.
Model Number C4-SW120277-xx
Power Requirements 120-277VAC +/-10%, 50/60Hz
This device requires a neutral connection. See
the “Sample Wiring Configurations” later in this
guide.
Power Consumption 120V: 400mW
277: 1150mW
Load Types and Ratings
Supported Load Types Incandescent, Halogen, Electronic (Solid
State) Low Voltage (ELV) transformers,
Magnetic (Iron Core, Inductive) Low Voltage
(MLV) transformers, Fluorescents, Compact
Fluorescents, LEDs, Motors
Maximum Load 120V: 15A, 1/2HP
277V: 8A, 1/2HP
Environmental
Operational Temperature 32˚ F - 104˚ F (0˚ C - 40˚ C)
Humidity 5% to 95% non-condensing
Storage -4˚ F - 158˚ F (-20˚ C - 70˚ C)
Miscellaneous
Control Communications ZigBee, IEEE 802.15.4, 2.4 GHz, 15-channel
spread spectrum radio
Wallbox Volume 5.75 cubic inches
Weight 0.12 lb (0.05 kg)
Shipping Weight 0.18 lb (0.08 kg)
Switch
Installation Guide