• Home
• Brands
• Bloomfield Manuals
• Bloomfield MOD-400
• Bloomfield MOD-400 Specifications

Bloomfield MOD-400 Specifications

Download Installation instructions of Bloomfield MOD-400 Coffee Maker, Food Warmer for Free or View it Online on All-Guides.com. This version of Bloomfield MOD-400 Manual compatible with such list of devices, as: MOD-400, MOD-400D, MOD-400T, MOD-400TD, MOD-400TDM

1

(152)

6

(356)

14

(197)

7 3/4

(860)

33 7/8

(57)

2 1/4

(600)

23 5/8

(1461)

57 1/2

(457)

18

(159)

6 1/4

(248)

9 3/4

(44)

1 3/4

(889)

35

(572)

22 1/2

(1435)

56 1/2

(127)

5

(79)

3 1/8

(430)

16 7/8

ELECTRICAL CODES.

NOTE: INSTALLATION MUST MEET LOCAL PLUMBING AND

volts to ground.

2. Do not connect to a circuit operating at more than 150

Panel. Check nameplates for voltage and phase.

knockout to terminal block supplied within the Master Control

supply leads (see 'wiring requirements' label) through conduit

1. Final connection is accomplished by bringing proper power

TO WIRE:

3. Connect 1'' drain connection to suitable drain line.

female N.P.T. drains.

2. Warmers with 'D" suffix are supplied with individual 1/2''

one end of the manifold.

discretion of the fabricator. Install and tighten pipe plug in

Model "DM" and "TDM" units. Location of valve handle is at the

1. A drain manifold complete with valve is supplied on all

TO PLUMB:

supplied.

4. Mount Control Panel onto electrical box using screws

MOD-400 AND MOD-400T MODELS

SPECIFICATIONS AS THE STANDARD

SUFFIX HAVE THE SAME ELECTRICAL

ALL MODELS WITH A 'D' OR 'DM'

FIELD WIRING GAUGE

3 PHASE

17.3

11.2208 3600

MOD-400

AMPS PER LINE 3 PHASE

VOLTS WATTSMODELS

SINGLE

20.0

13.0

240

4800

MOD-400

23.8

14.5

208

4960

MOD-400T

27.5

17.8240 6600

MOD-400T

11.2

13.0

14.5

17.8 11.3

9.8

8.7

7.5

AMPS

PHASE

'T' MODELS

'T' MODELS

'D' MODELS ONLY

INTERNAL N.P.T.

1/2 INCH

WELLS/BLOOMFIELD * VERDI, NV

PANEL

CONTROL

MASTER

FRONT PANEL CUTOUTTOP CUTOUT

SCREWDRIVER

COUNTERTOP

WELLSLOK

GASKET

WARMER FLANGE

FRONT OF THE FIXTURE.

MANIFOLD ARE LOCATED TO THE

THE CONTROL PANEL AND DRAIN

MOUNT APPLIANCE SO THAT BOTH

IMPORTANT:

3. Mount Control Box to apron cutout as shown in drawing.

required to secure flange tightly to countertop.

Wellslok frame and twist "ears" outward (clockwise) as

2. From underneath, insert screwdriver into "slots" in

flange.

to underside of gray gasket material supplied on mounting

to countertop, apply a bead of silicone adhesive/sealant

RECOMMENDATION: Before final seating of modular section

modular section into countertop cutout and position.

countertop cutout, then through apron cutout. Lower

1. Tilt and pass Control Panel and electrical box through

Master Control Panel when making installation.

IMPORTANT - DO NOT disconnect "lead wires" from the

TO INSTALL:

4. Unit shall be accessible for servicing from the bottom.

3. Cut out holes.

apron using the control box as a template.

2. Layout and fabricate control panel holes in counter

apron.

1. Layout "cutout" dimensions on countertop and front

TO FABRICATE:

the unit to avoid contact with elevated temperatures.

recommended that a baffle be placed 8 1/2 inches below

3. If storage is to be used underneath the unit, it is

2. Unit shall be accessible for servicing from the bottom.

6 3/4 inches to a surface below the unit.

6 inches to front wall, 1 inch to back and side walls, and

Wooden and Metal Installation: DO NOT install closer than

1. Required Installation Clearances:

OUTLINED BELOW UPON INSTALLATION:

INSTALLER MUST MEET CONDITIONS OF ACCEPTABILITY

FOR DM AND TDM MODELS ONLY.

MANIFOLD WITH 1" INTERNAL NPT VALVE IS SUPPLIED

ARE FIELD CONVERTIBLE TO SINGLE PHASE. THE DRAIN

NOTE: MOD-400 UNITS ARE SHIPPED THREE PHASE AND

CUTOUT DETAILS

INSTALLATION INSTRUCTIONS

37099-4 REV (-)

INSTALLATION INSTRUCTIONS

BUILT-IN MODULAR WARMERS

MOD 400 SERIES (D, TD, TDM)

(25) (25) (171) (152)

MINIMUM CLEARANCE REQUIRED FROM

BACK SIDE BOTTOM FRONT

1 1 6 3/4 6

ELECTRICAL

CLEARANCES

PRODUCT DIMENSIONS

UNITS TO THE NEAREST SURFACE

L3L2L1

1 PHASE

TEMP.

RATING

75°C

75°C

75°C

75°C

INCHES

(MM)

12 AWB Cu

12 AWB Cu

12 AWB Cu

12 AWB Cu

10 AWB Cu

10 AWB Cu

8 AWB Cu

8 AWB Cu