Juniper SRX210 Getting Started Manual

Download Getting started manual of Juniper SRX210 - DESK MOUNTING KIT Gateway, Network Accessory for Free or View it Online on All-Guides.com.

Juniper SRX210 - DESK MOUNTING KIT Getting started manual - Page 1
1
Juniper SRX210 - DESK MOUNTING KIT Getting started manual - Page 2
2
Juniper SRX210 - DESK MOUNTING KIT Getting started manual - Page 3
3
Juniper SRX210 - DESK MOUNTING KIT Getting started manual - Page 4
4
Getting Started Guide
V
Use the instructions in this guide to help you connect the SRX210 Services Gateway to your network. For details, see the
SRX210 Services Gateway Hardware Guide at http://www.juniper.net/techpubs/a057.html.
SRX210 Services Gateway
PART 1 - CONNECTING AND CONFIGURING THE DEVICE
Use the instructions below to connect and set up the SRX210 Services Gateway to protect your network. Refer to the LEDs on the
front panel of the device to help you determine the status of the device.
SRX210 Services Gateway (Low Memory and High Memory)
The following four types of SRX210 Services Gateways are available:
Device DDR Memory PoE Voice Support
SRX210B 512 MB No No
SRX210H 1 GB No No
SRX210H-POE 1 GB Yes No
SRX210-P-MGW 1 GB Yes Yes
Note: On the SRX210H-PoE and SRX210-P-MGW
models, Power over Ethernet (PoE) of 50 watts is
supported across 4 ports (ge-0/0/0, ge-0/0/1, fe-0/0/2,
and fe-0/0/3).
Step 1
Connect the power cable to the device and a power source. We
recommend using a surge protector. Note the following indications:
Power LED (green): The device is receiving power.
Status LED (green): The device is operating normally.
Note: You must allow the device between 5 and 7 minutes to boot up after
you have powered it on. Wait until the Status LED is solid green before
proceeding to the next step.
Step 2
Connect the management device to the services gateway using either of
the following methods:
Connect an Ethernet cable from one of the following ports to the
Ethernet port on the management device (workstation or laptop):
•ge-0/0/1
fe-0/0/2 through fe-0/0/7
We recommend this connection method. If you are using this
method to connect, proceed with Step 3.
Connect an RJ-45 cable from the console port to the supplied DB-9
adapter, which then connects to the serial port on the management
device. (Serial port settings: 9600 8-N-1-N).
If you are using this method to connect, proceed with the CLI
configuration instructions available in the Quickstart Guide for
Branch SRX Series Services Gateways at
http://www.juniper.net/us/en/local/pdf/app-notes/3500153-en.pdf.
Step 3
Ensure that the management device acquires an IP address on the
192.168.1/24 subnetwork (other than 192.168.1.1) from the device.
The interfaces have following factory-default settings:
Notes:
The services gateway functions as a DHCP server and will assign an IP
address to the management device.
If an IP address is not assigned to the management device, manually
configure an IP address in the 192.168.1.0/24 subnetwork. Do not
assign the 192.168.1.1 IP address to the management device, as this IP
address is assigned to the device. By default, the DHCP server is
enabled on the L3 VLAN interface, (IRB) vlan.0 (ge-0/0/1 and fe-0/0/2
to fe-0/0/7), which is configured with an IP address of 192.168.1.1/24.
When an SRX210 Series Services Gateway is powered on for the first
time, it boots using the factory default configuration.
Step 4
Access the J-Web interface:
1. Launch a Web browser from the management device.
2. Enter 192.168.1.1 in the URL address field.
3. Specify the default user name as root. Do not enter any value in the
Password field.
Interface Security Zone DHCP State IP Address
ge-0/0/0 untrust client unassigned
ge-0/0/1 and fe-0/
0/2 to fe-0/0/7
trust server 192.168.1.1/24
SRX210 Services Gateway (Power over Ethernet)
SRX210 Services Gateway with Integrated Convergence Services