• Home
• Brands
• Extron electronics Manuals
• Extron electronics Decora Style1-Gang Wallplate WP CTL D
• Extron electronics Decora Style1-Gang Wallplate WP CTL D Installation Manual

Extron electronics Decora Style1-Gang Wallplate WP CTL D Installation Manual

Download Installation manual of Extron electronics Decora Style1-Gang Wallplate WP CTL D Network Hardware for Free or View it Online on All-Guides.com.

1

1. Using a mud ring or a junction box as a guide, mark the holes and cut out the

material within the marked area.

N

If installing a junction box, allow enough depth for

the wall plate and cables.

The box should be at least 2.0” (5.1 cm) deep to

accommodate the connectors, plate, and cables.

2. Either

  •Insertthemudringintotheopening,rotate

 thedoglegs,andsecurewiththescrewsprovided,

or

•Insertthewallboxandsecurewith10-pennynails

or screws.

3.  RuntheRS-232andIRsignalcablesbehindthewall

and thread them through the mud ring or wall box.

N Extron recommends using a good quality, low

capacitance, shielded cable such as an Extron

CTL or SPL Control cable.

Decora

Faceplate

Extron

WP CTL D

Wall

Wall Mounting

Bracket

G

S

IR

G

Rx

Tx

Serial

WP CTL D Installation Guide

TheExtronWPCTLDisaDecorastyle1-gangwallplatewhichpassesRS-232controlsignals

fromacomputerorcontrolsystem,andIRsignalsfromanIRsource.

Installitdirectlyintothewallusingamudring,orina1-gangjunctionbox(notsupplied),

followingthestepsbelow.

4. ConnecttheIRcabletotherearpanelIR

connectorbyinsertingthesignalwireinto

the hole marked "S" , and the ground wire

intotheholemarked"G"(seeinset,step4).

N

The recommended driving distance from

an MLC controller is 100 feet.

5. ConnecttheRS-232cabletotherearpanelRS-232

connectorbyinsertingthegroundwireintothehole

marked "G", the transmit wire into the hole marked

"Tx",andthereceivewireintotheholemarked

"Rx"(seeinset,step5).

6. Mountthedeviceintothemudringorwallbox.

7. AttachthesuppliedDecorafaceplate.

N If applicable, repeat steps 1-7 to install additional wall plates.

8.  ConnecttheRS-232controldeviceand/orIRinputdevicetothefrontoftheWPCTLD.

Extron USA - West

Headquarters

+800.633.9876

Inside USA / Canada Only

+1.714.491.1500

+1.714.491.1517 FAX

Extron USA - East

+800.633.9876

Inside USA / Canada Only

+1.919.863.1794

+1.919.863.1797 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+800.7339.8766

Inside Asia Only

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+400.883.1568

Inside China Only

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Dubai

+971.4.2991800

+971.4.2991880 FAX

68-1618-01

Rev B 08 08

WP CTL D Installation Guide, cont’d

Step 5

Step 4

G

Tx

Rx

WP CTL D

IR Out

White striped wire

S = Signal (IR)

G = Ground

G S

IR Emitter

100'

(30.5 m)