• Home
• Brands
• Broan-NuTone Manuals
• Broan-NuTone 695C
• Broan-NuTone EC50 Installation Instructions

Broan-NuTone EC50 Installation Instructions

Download Installation instructions of Broan-NuTone 695C Ventilation Hood for Free or View it Online on All-Guides.com. This version of Broan-NuTone 695C Manual compatible with such list of devices, as: 695C, 696NC, EC50, EC70, VSBP50M

1

2

3

4

INSTALLATION INSTRUCTIONS

ECONOMY VENTILATION FAN

MODELS: EC50 & EC70, 696NC & 695C, VSBP50M

HOUSING INSTALLATION

Rough Opening: 8¼” long x 7¼” wide

Housing Size: 7

3

⁄16” x 8

1

⁄16” x 3

7

⁄8”

Refer to Figure 1A. Remove motor plate from housing before

mounting. Insert screwdriver between motor plate and side of

housing with duct collar. Gently pry the housing away from the

motor plate while pulling up on the motor plate to disengage the

plate from the housing.

1. With nails or screw, secure (but do not tighten) the housing to the

ceiling or wall through the two keyhole slots in the mounting tabs.

NOTE: Prior to completely tightening, adjust the housing so

that the outer edge will remain 1/8” to 1/4” recessed

from the finished ceiling or wall. For the grille to fit

properly, the housing must not extend outside the

finished wall surface.

2. Secure discharge adapter over flange on housing and connect

ducting to discharge, make sure housing is securely mounted

to prevent fan from vibrating and causing noise.

WIRING

IMPORTANT: Ensure all wiring complies with local codes and the

unit is properly grounded.

1. Refer to Figure 2. Run power leads from the wall or timer

switch to the unit.

2. Using approved wire connectors, connect supply wires to fan

wires: BLACK to BLACK and WHITE to WHITE. Connect

ground wire (GREEN to bare) to the GREEN ground screw in

the fan’s junction box.

30040605C

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer.

If you have questions, contact the manufacturer at the

address or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service

panel and lock service disconnecting means to prevent

power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service

panel.

3. Installation work and electrical wiring must be done by

qualified personnel in accordance with all applicable codes

and standards, including fire-rated construction codes and

standards.

4. Sufficient air is needed for proper combustion and exhausting

of gases through the flue (chimney) of fuel burning equipment

to prevent backdrafting. Follow the heating equipment

manufacturer’s guidelines and safety standards such as

those published by the National Fire Protection Association

(NFPA), and the American Society for Heating, Refrigeration

and Air Conditioning Engineers (ASHRAE), and the local

code authorities.

5. When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. To reduce the risk of fire and electric shock, do not use this

fan with any solid-state speed control device.

8. Suitable for use over a tub or shower when connected to a

GFCI (Ground Fault Circuit Interrupter) - protected branch

circuit.

9. This unit must be grounded.

10. When applicable local regulations comprise more restrictive

installation and/or certification requirements, the aforementioned

requirements prevail on those of this document and the

installer agrees to conform to these at his own expenses.

11. When performing installation, servicing or cleaning the unit, it is

recommended to wear safety glasses and gloves.

1. For general ventilating use only. Do not use to exhaust

hazardous or explosive materials and vapors.

2. Do not mount this product in a ceiling insulated to a value

greater than R40. This product is designed to be mounted in

a ceiling or in a standard 2” x 4” wall.

3. Do not use this product in kitchens.

4. To avoid motor bearing damage and noisy and/or unbalanced

impeller, keep drywall spray, construction dust, etc. off power

unit.

5. Please read specification label on product for further

information and requirements.

READ AND SAVE THESE INSTRUCTIONS

!

CAUTION

SECURE

FAN TO

HOUSING

PLUG INSERTS

INTO HOUSING’S

RECEPTACLE

TABS

SLOTS

FIGURE 1

FIGURE 1A

MOUNTING

TABS (TYP.)

BLACK

BE0009A

WHITE

FAN

HOUSING

SWITCH

BOX

WHITEBLACK

120 V AC, 60 Hz

HOUSE POWER

FIGURE 2

REGISTER YOUR PRODUCT ONLINE AT

• For Broan EC50 or EC70: www.broan.ca

• For NuTone 696NC or 695C: www.nutone.ca