Cisco TelePresence System Installing

Download Installing of Cisco TELEPRESENCE Conference System, Network Router for Free or View it Online on All-Guides.com.

Cisco TELEPRESENCE Installing - Page 1
1
Cisco TELEPRESENCE Installing - Page 2
2
Cisco TELEPRESENCE Installing - Page 3
3
Cisco TELEPRESENCE Installing - Page 4
4
Installing Cisco TelePresence System Profile 65
Page 178-19779-02 Profile 65 Installation Sheet | April 2012 | © 2010-2012 Cisco Systems, Inc. All rights reserved.
1
Unpacking the foot module
4
Key lock and levelling adjustment
3
Mounting the column to the foot module to complete the bottom module
MOUNTING THE BOTTOM MODULE
1. Lift the column and place it carefully
on the foot module.
2. When looking down through the
column you can see the four screws
in the foot module.
Make sure the screws enter the
corresponding holes in the column.
3. Open the front door to access the
screws. Secure the column to the
foot module with four nuts. The nuts
are found in the plastic bag. See the
illustration to the right.
When the bottom module is finished,
the hole in the foot module should be
visible on the rear side only.
PERSON 1:
Lift here.
PERSON 2:
Lift here.
The illustration shows the stand-alone
foot module. The wall stand foot module
is mounted in the same way.
2
Unpacking the unit
PRECAUTIONS
Follow the steps in this installation guide when unpacking and
assembling the Profile 65”.
A minimum of four (4) persons are required during the installation of the
system.
• The monitor box requires four (4) persons to lift.
• The column requires two (2) persons to lift.
• The foot module requires two (2) persons to lift.
NOTE: The floor must be in level.
WEIGHTS OF THE DIFFERENT UNITS PACKAGING INCLUDED
• Monitor box: 110 kg / 243 lbs
• Column: 40 kg / 88 lbs
• Foot module box: 25 kg / 55 lbs
• Accessories, camera, Touch 8” and grille boxes: 8 kg / 17.6 lbs
UNPACKING THE SYSTEM AT THE DESTINATION
It is highly recommended to start the unpacking and assembling of
Profile 65” at the place where the system is to be used.
Check the dimensions of the lift if you need to use a lift for the
transportation.
Outer dimensions and total weight of the main unit (package included):
• Height: 145 cm / 57.1 in.
• Width: 76 cm / 29.9 in.
• Length: 170 cm / 66.9 in.
• Weight: 183 kg / 402 lbs
NOTE: If it is not possible to bring the main unit to the destination,
follow step 1–2 and bring the smaller units to the destination.
DIMENSIONS WHEN ASSEMBLED
The Profile 65” system has the following dimensions:
• Height: 167 cm / 65.7 in.
• Width: 153 cm / 60.3 in.
• Depth: Stand-alone: 66 cm / 26 in.
Wall stand, with short bracket: 44.7 cm / 17.6 in.
Wall stand, with long bracket: 52.2 cm / 20.6 in.
USER DOCUMENTATION
User guides and compliance and safety information for this product are
available on the Cisco web site: http://www.cisco.com/go/profile-docs
The Video conferencing room primer and Video conferencing room
acoustics guidelines documents contain information about optimizing a
meeting room for video conferencing.
PROFILE 65” IS DELIVERED WITH:
Monitor
Column
Foot module (stand-alone or wall stand)
Grille
Camera
Touch 8” interface device
Remote control
Microphones
Accessories
FOOT MODULE 25 KG / 55 LBS
1. Open the snap lockers
2. Lift out the foot module box
MONITOR BOX
(110 kg / 243 lbs)
CAUTION
HEAV Y
AND
BULKY
REQUIRES:
4 PEOPLE TO LI FT
CAUTION
HEAV Y
AND
BULKY
REQUIRES:
2 PEOPLE TO LI FT
STAND-ALONE FOOT MODULE
WALL STAND FOOT MODULE
ACCESSORIES TO THE FOOT MODULE
• Orange level adjustment tool
• 4 × Nuts
• Wall brackets (wall stand only)
• Spacer (wall stand only)
• Allen key (wall stand only)
COLUMN
(40 kg / 88 lbs)
ACCESSORIES BOX
• Power cables
• Microphones
• Remote control
• Batteries
• Wrench
• Key lock tool
• Gloves
• Cleaning cloth
The illustration shows
a cross section of
the bottom module
(column and foot
module).
Fasten the 4 nuts
(two on each side
of the system).
Outer cover
Camera box
Grille box
Accessories box
Foam to protect
the column
Column
Monitor box
1. Place the unit on a stable surface.
2. Open the snap lockers to remove
outer cover.
3. Locate the different parts.
4. Lift out the camera, Touch 8”,
grille and accessories boxes.
5. Remove the packaging above and
around the column and monitor
box.
Lift out to open
the snap lockers.
KEY LOCK
Place the orange key on the key
lock and turn clockwise to lock,
counterclockwise to unlock.
The level adjustment tool is found in
the foot module box. The key lock
tool is found in the accessories box.
ADJUST UP
Place the level adjustment tool as
illustrated. Seen from above, turn
clockwise to adjust the height up.
ADJUST DOWN
Place the level adjustment tool at
the opposite side of the wheel.
Turn counterclockwise to adjust
the height down.
Lock
Unlock
Touch 8” box
CAUTION
HEAVY
Lift out to open
the snap lockers.
Front
-
Eagle
117000 rev.
rev. 00Z+ is master3D CAD model file 117000
-
Telecom AS
-
-
-
-
-
UL reference:
Processes
Flame class requirement: -
Dimensions without paint or finish
Flame class:
must comply with the RoHS directives
Sheet 1 of 1
All materials, finishes, and proccesses
projection
Unit:
1:10
Tolerances
MaterialSpecification:
Surface treatment
Scale:
Sheet size:
mm
A4
Part weight: 108964g
European
Glossiness:
Surface:
Color:
Thickness:
Type number:
Manufacturer:
-
-
-
-
-
Type: -
-
-
-
-
-
-
-
-
Rev. Date Prep. Checked Change
Rev. Date Prep. Checked Change
-
Eagle
117000 rev.
rev. 00Z+ is master3D CAD model file 117000
-
Telecom AS
-
-
-
-
-
UL reference:
Processes
Flame class requirement: -
Dimensions without paint or finish
Flame class:
must comply with the RoHS directives
Sheet 1 of 1
All materials, finishes, and proccesses
projection
Unit:
1:10
Tolerances
MaterialSpecification:
Surface treatment
Scale:
Sheet size:
mm
A4
Part weight: 108964g
European
Glossiness:
Surface:
Color:
Thickness:
Type number:
Manufacturer:
-
-
-
-
-
Type: -
-
-
-
-
-
-
-
-
Front
Front