Bunn LCR-3 HV Installation & Operating Manual

Download Installation & operating manual of Bunn LCR-3 HV Beverage Dispenser for Free or View it Online on All-Guides.com.

Brand: Bunn

Category: Beverage Dispenser

Type: Installation & operating manual for Bunn LCR-3 HV

Pages: 27 (1.92 Mb)

Download Bunn LCR-3 HV Installation & operating manual

Bunn LCR-3 HV Installation & operating manual - Page 1
1
Bunn LCR-3 HV Installation & operating manual - Page 2
2
Bunn LCR-3 HV Installation & operating manual - Page 3
3
Bunn LCR-3 HV Installation & operating manual - Page 4
4
Bunn LCR-3 HV Installation & operating manual - Page 5
5
Bunn LCR-3 HV Installation & operating manual - Page 6
6
Bunn LCR-3 HV Installation & operating manual - Page 7
7
Bunn LCR-3 HV Installation & operating manual - Page 8
8
Bunn LCR-3 HV Installation & operating manual - Page 9
9
Bunn LCR-3 HV Installation & operating manual - Page 10
10
Bunn LCR-3 HV Installation & operating manual - Page 11
11
Bunn LCR-3 HV Installation & operating manual - Page 12
12
Bunn LCR-3 HV Installation & operating manual - Page 13
13
Bunn LCR-3 HV Installation & operating manual - Page 14
14
Bunn LCR-3 HV Installation & operating manual - Page 15
15
Bunn LCR-3 HV Installation & operating manual - Page 16
16
Bunn LCR-3 HV Installation & operating manual - Page 17
17
Bunn LCR-3 HV Installation & operating manual - Page 18
18
Bunn LCR-3 HV Installation & operating manual - Page 19
19
Bunn LCR-3 HV Installation & operating manual - Page 20
20
Bunn LCR-3 HV Installation & operating manual - Page 21
21
Bunn LCR-3 HV Installation & operating manual - Page 22
22
Bunn LCR-3 HV Installation & operating manual - Page 23
23
Bunn LCR-3 HV Installation & operating manual - Page 24
24
Bunn LCR-3 HV Installation & operating manual - Page 25
25
Bunn LCR-3 HV Installation & operating manual - Page 26
26
Bunn LCR-3 HV Installation & operating manual - Page 27
27
22
Check Pump & Flow Rate Calibration, refer
to Field Calibration Procedures
The calculated Target RPM for
the pump indicated is out of
range
____ TARGET RPM
TOO HIGH !!
Replace BIB, see Loading the Concentrate
Check BIB Connector Fittings
Check Tubing Installation
Check Empty BIB Threshhold, see Field
Calibrating the Epmty BIB Warning
Concentrate BIB is empty.
BIB not properly connected.
Tubing kinked or blocked.
Empty BIB Threshhold too high.
XXXX BIB EMPTY
Replace BIB Soon
Rinse Dispenser, see Rinse Procedure
Replace BIB, see Loading the Concentrate
Rinse Alarm Time Interval has
expired
RINSE REQUIRED
Wait for water temp to rise
Check Ready Temp. threshhold setting
Service Required
Water temp is below the preset
READY temp
HEATING
Please Wait!
Check Master ON/OFF Switch
Check Power Cord & Circuit Breaker
Service Required
No Power to the Dispenser
NO DISPLAY
Troubleshooting
A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems
encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic
Technical Service Department.
Only qualified service personnel should perform inspection, testing, and repair of electrical equipment.
Shorting the terminals or the application of external voltages to electronic components may result in component
or circuit board failure.
Intermittent operation of electronic circuit boards is unlikely. board failure will normally be permanent. If an
intermittent condition is encountered, the cause will likely be a switch contact or a loose wire connection at
a terminal or crimp.
Solenoid removal requires interrupting the water supply to the valve. Damage may result if solenoids are
energized for more than ten minutes without a supply of water.
The use of two wrenches is recommended whenever plumbing fittings are tightened or loosened. This will
help avoid twists and kinks in the tubing.
Make certain that all plumbing connections are sealed and all electrical connections are tight and isolated.
This dispenser is heated at all times. Keep away from combustibles.
WARNING:
Exercise extreme caution when servicing electrical equipment.
Disconnect the brewer from the power source when servicing, except when electrical tests are specified.
Follow recommended service procedures.
Replace all protective shields or safety notices.
Screen Displayed Possible Cause Troubleshooting Procedures
41129 052208