Bunn LCR-3 HV Installation & Operating Manual

Download Installation & operating manual of Bunn LCR-3 HV Beverage Dispenser for Free or View it Online on All-Guides.com.

Brand: Bunn

Category: Beverage Dispenser

Type: Installation & operating manual for Bunn LCR-3 HV

Pages: 27 (1.92 Mb)

Download Bunn LCR-3 HV Installation & operating manual

Bunn LCR-3 HV Installation & operating manual - Page 1
1
Bunn LCR-3 HV Installation & operating manual - Page 2
2
Bunn LCR-3 HV Installation & operating manual - Page 3
3
Bunn LCR-3 HV Installation & operating manual - Page 4
4
Bunn LCR-3 HV Installation & operating manual - Page 5
5
Bunn LCR-3 HV Installation & operating manual - Page 6
6
Bunn LCR-3 HV Installation & operating manual - Page 7
7
Bunn LCR-3 HV Installation & operating manual - Page 8
8
Bunn LCR-3 HV Installation & operating manual - Page 9
9
Bunn LCR-3 HV Installation & operating manual - Page 10
10
Bunn LCR-3 HV Installation & operating manual - Page 11
11
Bunn LCR-3 HV Installation & operating manual - Page 12
12
Bunn LCR-3 HV Installation & operating manual - Page 13
13
Bunn LCR-3 HV Installation & operating manual - Page 14
14
Bunn LCR-3 HV Installation & operating manual - Page 15
15
Bunn LCR-3 HV Installation & operating manual - Page 16
16
Bunn LCR-3 HV Installation & operating manual - Page 17
17
Bunn LCR-3 HV Installation & operating manual - Page 18
18
Bunn LCR-3 HV Installation & operating manual - Page 19
19
Bunn LCR-3 HV Installation & operating manual - Page 20
20
Bunn LCR-3 HV Installation & operating manual - Page 21
21
Bunn LCR-3 HV Installation & operating manual - Page 22
22
Bunn LCR-3 HV Installation & operating manual - Page 23
23
Bunn LCR-3 HV Installation & operating manual - Page 24
24
Bunn LCR-3 HV Installation & operating manual - Page 25
25
Bunn LCR-3 HV Installation & operating manual - Page 26
26
Bunn LCR-3 HV Installation & operating manual - Page 27
27
26
Field Calibrating the Empty BIB Warning
The dispenser will automatically display LEFT, MIDDLE or RIGHT BIB Empty when the corresponding Concentrate
BIB is Empty. The Refill message is triggered when the Conductance Sensor reading drops below the minimum
setting. The factory set minimum is 600 and should be correct for most locations. However, the hardness of the
local water supply may affect this reading. If the Refill message doesn’t come on when the BIB is empty or the
message comes on too early and there is still concentrate left in the BIB, use the following procedure to find the
correct Empty BIB threshold.
Note: Increasing the threshold slightly will cause the Empty BIB warning to come on sooner. Lowering the
threshold will draw more concentrate from the BIB, but could allow dispensing of weak coffee.
1. Set the Function Switch to the “Rinse” position.
2. Place a 1/2 gal or larger container under the dispense tip, then activate and hold the left dispenser.
3. Dispense long enough to rinse all the concentrate out of the mix chamber and for the conductance reading
“COND” on the LCD to stabilize and stop dropping.
4. Record the nominal Conductance value displayed. (NOTE: It is typical for this value fluctuate (+/- 25) points
about the nominal value}. This is the conductance reading of the water in your area.
5. Add 100 points to Conductance value. This is the new Empty BIB threshold value for your dispenser.
6. Enter this new value into the Empty BIB Alarm threshold, see Programming the Dispenser.
41129 052208