York B1HA018A06 Installation Instruction

Download Installation instruction of York B1HA018A06 Heat Pump for Free or View it Online on All-Guides.com. This version of York B1HA018A06 Manual compatible with such list of devices, as: B1HA018A25, B1HA030A06, B1HA030A58, B1HA042A06, B1HA048A06

York B1HA018A06 Installation instruction - Page 1
1
York B1HA018A06 Installation instruction - Page 2
2
York B1HA018A06 Installation instruction - Page 3
3
York B1HA018A06 Installation instruction - Page 4
4
York B1HA018A06 Installation instruction - Page 5
5
York B1HA018A06 Installation instruction - Page 6
6
York B1HA018A06 Installation instruction - Page 7
7
York B1HA018A06 Installation instruction - Page 8
8
York B1HA018A06 Installation instruction - Page 9
9
York B1HA018A06 Installation instruction - Page 10
10
York B1HA018A06 Installation instruction - Page 11
11
York B1HA018A06 Installation instruction - Page 12
12
York B1HA018A06 Installation instruction - Page 13
13
York B1HA018A06 Installation instruction - Page 14
14
York B1HA018A06 Installation instruction - Page 15
15
York B1HA018A06 Installation instruction - Page 16
16
York B1HA018A06 Installation instruction - Page 17
17
York B1HA018A06 Installation instruction - Page 18
18
York B1HA018A06 Installation instruction - Page 19
19
York B1HA018A06 Installation instruction - Page 20
20
York B1HA018A06 Installation instruction - Page 21
21
York B1HA018A06 Installation instruction - Page 22
22
York B1HA018A06 Installation instruction - Page 23
23
York B1HA018A06 Installation instruction - Page 24
24
GENERAL
YORK Model B1HA units are factory assembled heat pumps
designed for outdoor installation on a rooftop or a slab. Field-
installed electric heater accessories are available to provide
supplemental electric heat combined with electric cooling and
heating.
The units are completely assembled on rigid, removable
base rails. All piping, refrigerant charge, and electrical wiring
is factory installed and tested. The units require only electric
power and duct connections at the point of installation.
The electric heaters have nickel-chrome resistance wire ele
-
ments and utilize single point power connection.
INSPECTION
As soon as a unit is received, it should be inspected for pos
-
sible damage during transit. If damage is evident, the extent
of the damage should be noted on the carrier's freight bill. A
separate request for inspection by the carrier's agent should
be made in writing. Refer to Form 50.15-NM for additional in
-
formation.
REFERENCE
Additional information on the design, installation, operation
and service of this equipment is available in the following refer-
ence forms:
55.70-N1 -General Installation
55.70-N2 -Pre-start & Post-start Check List
511.26-N1.1V -Electric Heater Accessory
RENEWAL PARTS
Refer to Replacement Parts Manual for complete listing of
replacement parts on this equipment.
All forms referenced in this instruction may be ordered from:
Standard Register
2101 West Techumseh Road
Norman, OK 73069
Toll Free: Tel. 877-318-9675/Fax. 877-379-7920
CHAMPION® SERIES
SINGLE PACKAGE HEAT PUMPS
Supersedes: 035-16004-000 (0801)
035-16004-001-A-0202
INSTALLATION INSTRUCTION

MODELS B1HA018 THRU 060
1.5 THRU 5 TON
(10 SEER)
Installer should pay particular attention to the words: NOTE, CAUTION and WARNING. Notes are intended to clarify or
make the installation easier. Cautions
are given to prevent equipment damage. Warnings are given to alert installer that per
-
sonal injury and/or equipment damage may result if installation procedure is not handled properly.
CAUTION
THE ENCLOSED INSTALLATION INSTRUCTIONS AND ANY APPLICABLE
LOCAL, STATE, AND NATIONAL CODES INCLUDING, BUT NOT LIMITED
TO, BUILDING, ELECTRICAL, AND MECHANICAL CODES.
THIS PRODUCT MUST BE INSTALLED IN STRICT COMPLIANCE W ITH
WARNING
OPERATION OF THE PRODUCT COULD CAUSE PERSONAL INJURY
OR PROPERTY DAMAGE.
INCORRECT INSTALLATION MAY CREATE A CONDITION WHERE THE