• Home
• Brands
• System Sensor Manuals
• System Sensor M200G-RF
• System Sensor M200G-RF Installation Instructions Manual

System Sensor M200G-RF Installation Instructions Manual

Download Installation instructions manual of System Sensor M200G-RF Gateway for Free or View it Online on All-Guides.com.

1

2

3

4

5

6

7

8

9

10

D200-303-00 I56-3892-002 Pittway Tecnologica S.r.l. Via Caboto 19/3, 34147 TRIESTE, Italy

DESCRIPTION

The M200G-RF is an advanced RF device designed for use

with addressable intelligent re systems that use a compatible

proprietary communication protocol for monitoring and control.

The gateway contains a wireless transceiver that enables bi-

directional RF communication between System Sensor radio re

detection and signalling devices and the CIE controlling the re

alarm system.

This device conforms to EN54-25, EN54-17 and EN54-18. It

complies with the requirements of 2014/53/EU for conformance

with the RED directive.

SPECIFICATIONS

Comm. Loop Supply Voltage: 15 – 29 V Direct Current (Loop current ≤

900mA)

Max short circuit protection current: 900mA

Comm. Loop Standby Current: @ 24V: up to 510µA max depending on

(no loop communication) RF conguration (worst case 32 devices

in star conguration

Comm. Loop (poll once per 5s: @ 24V: up to 3.4mA max depending on

green LED blink) RF conguration (worst case 32 devices

in star conguration

Loop LED on current (max): Red 4mA, Amber 5.3mA

Power On initialisation time: 2 Secs (typical)

Radio Frequency: 865-870 MHz (up to 18 channels)

RF output power: 14dBm (max)

Range: 400m (typ. in free air)

RF communications with up to 32 RF devices

Relative Humidity: 10% to 93% (non-condensing)

Wiring: 0.75mm

2

– 2.5mm

2

max

The gateway must be powered by a limited power source with Safety Extra

Low Voltage (SELV) and with the required overload and short circuit protections

Gateway Loop Isolator

Isol. max. continuous current (switch closed): 0.9A (input voltage ≤ 29V)

Isolator max. switching current: 0.9A (input voltage ≤ 29V)

Max. isolation current (switch open): 15mA @ 24V

Max. series resistance (switch closed): 300 m ohm

INSTALLATION

This equipment and any associated wiring work must be installed

in accordance with all relevant codes and regulations.

Figures 1 and 2 detail the installation of the B501AP base (further

instructions are available for this if required - see document ref.

D550-33-00).

Note

Spacing between radio system devices must be a Minimum of 1m

Anti-Tamper Feature

The base includes a feature that, when activated, prevents removal

of the gateway from the base without the use of a tool. See Figures

3a and 3b for details on this.

SETTING THE ADDRESS

Set the address by turning the two rotary decade switches on the

underside of the gateway (see gure 4 overleaf), using a screwdriver

to rotate the wheels to the desired address. The gateway will take

one module address on the loop. Select a number between 01 and

159 (Note: The number of addresses available will be dependent

on panel capability, check the panel documentation for information

on this). Record the address on the label attached to the base.

Insert the gateway into the base and rotate it clockwise until it locks

into place.

M200G-RF

RADIO SYSTEM GATEWAY

INSTALLATION INSTRUCTIONS

E N G L I S H

102 mm

42 mm

90g

-30°C

60°C

1

2

3

4

-

-

+

+

Figure 2: B501AP Wiring

1

2

3

4

50-60 mm

SHIELD

≤ M4

Figure 1: B501AP Mounting

ADDRESS TAG

B501AP

M200G-RF

COMPATIBLE CIE

Figure 3a: Activation of Tamper Resist Feature

PLASTIC LEVER

BREAK TAB AT DOTTED LINE BY

TWISTING TOWARDS CENTRE OF

BASE

Figure 3b: Removing Repeater From Base

USE A SMALL-BLADED SCREWDRIVER TO PUSH

PLASTIC IN THE DIRECTION OF THE ARROW

I 56- 3892- 002