• Home
• Brands
• VTech Manuals
• VTech DS3111-2 - DECT 6.0 Cordless Phone
• VTECH DS3111-2 Quick Start Manual

VTECH DS3111-2 Quick Start Manual

Download Quick start manual of VTech DS3111-2 - DECT 6.0 Cordless Phone Cordless Telephone, IP Phone for Free or View it Online on All-Guides.com.

1

NOTES:

1. Use only the power adapters and batteries supplied with your

VTech telephone.

2. For complete feature instructions, please refer to your user’s manual.

96-006499-050-100

IMPORTANT!

If your product is not working properly:

Refer to the Troubleshooting section of the user’s

manual.

Visit our website at www.vtechphones.com.

In Canada, go to www.vtechcanada.com.

Call our customer service at 1 (800) 595-9511.

In Canada, call 1 (800) 267-7377.

•

•

•

Telephone base & charger installation

We recommend that you install the telephone base away from

any electronic equipment and appliances such as personal

computers, computer routers, television sets, microwave ovens

or refrigerators. Avoid excessive heat, cold, dust or moisture.

Install the telephone base and charger as illustrated. Make

sure that the electrical outlet is not controlled by a wall switch.

If you subscribe to Digital Subscriber Line (DSL) high-speed

Internet service through your telephone line, you must have a

DSL lter between the telephone base and the telephone wall

jack. The lter prevents noise and caller ID problems caused

by DSL interference. Please contact your DSL service provider

for more information about DSL lters.

Make, receive and end calls

Make a call

• Press /FLASH or

,

listen for a dial tone, then dial the

telephone number.

-OR-

1. Dial the number (press

MUTE /REMOVE to make

corrections; press and hold REDIAL/PAUSE to insert a

dialing pause).

2. Press

/FLASH or to use the speakerphone.

Receive a call

• Press

/FLASH,

or any dialing keys (0-9,

*

or #) to

answer an incoming call.

End a call

• Press

OFF/CLEAR or put the handset back in the telephone

base or charger.

Voicemail setup

If you subscribe to voicemail service provided by your local

telephone company, this feature allows you to use the

VOICEMAIL, PLAY, SKIP and ERASE buttons to access

your voicemail. Before completing these steps, be sure

to have your access number and password (provided by

your local telephone company) to access your voicemail.

You will also need the codes to play, skip and erase your

messages. Contact your local telephone company for more

information.

To program the

ACCESS NUMBER button:

1. Press

MENU/SELECT when the handset is not in use.

2. Press or to select VOICEMAIL SETUP, then press

MENU/SELECT.

3. Press or to select ACCESS NUMBER, then press

MENU/SELECT.

4. Use the dial pad to enter the access number. Press

MUTE/REMOVE to delete characters if necessary.

5. Press MENU/SELECT. You will hear a conrmation tone.

To program the PASSWORD, PLAY, SKIP and ERASE

buttons, follow steps 1 and 2 above. Next, select the

command you wish to program, and press MENU/SELECT.

Use the dial pad to enter the corresponding code for that

command, and press MENU/SELECT to conrm.

To program a pause (for more details, refer to the user’s

manual):

1. Press

MENU/SELECT when the handset is not in use.

2. Press or to select VOICEMAIL SETUP, then press

MENU/SELECT twice.

3. The blinking cursor should be at the end of your access

number. Press and hold the REDIAL/PAUSE button until

a P appears.

4. Press MENU/SELECT. You will hear a conrmation tone.

NOTE:

You must program your voicemail buttons before you can access all

of the functions available with your voicemail.

Battery installation & charging

Install the handset battery by following these steps:

1. Press the tab and slide the battery compartment cover down.

2. Align the two holes of the battery plug with the socket pins

in the handset battery compartment, matching the red and

black wires of the color-coded label.

3. Place the battery in the compartment with the wires in the

lower right corner.

4. Align the cover at against the battery compartment, then

slide it up until it clicks into place.

For optimal performance, we recommend that you charge

the handset for 16 hours. You can keep the battery charged

by returning the handset to the telephone base or charger

after use. When the battery power is fully depleted, a full

recharge takes about 16 hours.

Quick start guide

for models DS3111-2/TM3111-2

Charger adapter

Electrical outlet not

controlled by a wall

switch

Place t h e h a n d s e t in the

telephone base or charger. The

CHARGE light is on when the

handset is properly positioned in

the telephone base or charger.

CHARGE light

Telephone base

power adapter

CHARGE light

BT8000/ BT6010

Telephone

wall jack

Electrical outlet

not controlled by

a wall switch

Telephone base power adapter

Charger adapter

Telephone line

cord

MANUFACTURED IN CHINA

COMPLIES WITH 47 CFR PART 68

REGISTRATION NO.: US:EW7W401B80-565600

RINGER EQUIVALENCE: 0.1B

USOC JACK: RJ11C/RJ11W

HAC FCC ID: EW780-5656-00

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO

THE FOLLOWING TWO CONDITIONS: 1) THIS DEVICE MAY NOT CAUSE HARMFUL

INTERFERENCE; AND 2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,

INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. PRIVACY OF

COMMUNICATIONS MAY NOT BE ENSURED WHEN USING THIS PHONE.

DC 6V 300mA

CLASS 2 POWER SOURCE ONLY

TELEPHONE

EQUIPMENT

DSL lter (not

included) required

if you have DSL

high-speed

internet service