Samsung WF461ABP/XAA Fast Track Troubleshooting

Download Fast track troubleshooting of Samsung WF461ABP/XAA Washer for Free or View it Online on All-Guides.com.

Brand: Samsung

Category: Washer

Type: Fast track troubleshooting

Model: Samsung WF461ABP/XAA , Samsung WF461ABW/XAA

Pages: 9

Download Samsung WF461ABP/XAA Fast track troubleshooting

Samsung WF461ABP/XAA Fast track troubleshooting - Page 1
1
Samsung WF461ABP/XAA Fast track troubleshooting - Page 2
2
Samsung WF461ABP/XAA Fast track troubleshooting - Page 3
3
Samsung WF461ABP/XAA Fast track troubleshooting - Page 4
4
Samsung WF461ABP/XAA Fast track troubleshooting - Page 5
5
Samsung WF461ABP/XAA Fast track troubleshooting - Page 6
6
Samsung WF461ABP/XAA Fast track troubleshooting - Page 7
7
Samsung WF461ABP/XAA Fast track troubleshooting - Page 8
8
Samsung WF461ABP/XAA Fast track troubleshooting - Page 9
9
Fast Track Troubleshooting
Model:
WF461ABP/XAA
WF461ABW/XAA
Revision Date 4-30-2012
Quick Test Mode
To enter press Spin, Soil, & Power simultane-
ously with the power off.
1. All LED’s light up and the washer beeps as it
enters the Quick Test Mode.
2. After the displaying the software version, LCD
will display Model information. If EEEE is displayed
the PCB ass’y is defective.
4. When the version is displayed, turn the Jog-Dial
CCW so that the “TST” is displayed. Press the fol-
lowing keys to test the various components:
Press Temp Key to cycle through the Water Valves
circuit test (lock the door first) in this order: Pre-Wash,
Bleach, Cold Main, Hot, & Steam, then off.
Press Spin Key to test Door Lock/Unlock circuit
Press Steam Level Key to test Circulation/Drain Pump.
Press Soil Key to test the Water/Steam Heater.
Press My Cycle to test the Blower motor
When either Test or Spin is displayed on the LCD,
press Start/Pause key to conduct the motor test.
Service Mode:
This mode allows more detailed operation tests and
troubleshooting, to enter press Signal & Extra Rinse
simultaneously with the power on.
While in Service Mode the following tests can be per-
formed:
Quick Spin Test = Delay Start & Extra Rinse: This accel-
erates the drum motor from 0 to maximum RPM over a
few minutes. Note: Stay with the washer during this test,
out of balance detection may be bypassed. Press the Start/
Pause button during the test to hold its spinning speed for 10
minutes before going back to Quick Spin Test Mode. Press
and hold the Delay Start & Extra Rinse button to continue.
Cycle Count = Press the Signal button to see how many
times
the unit was used
Soft Ware # = Press the Soil button to see the software ver-
sion
information
Fault Code Test = Press the Spin button to view the stored
fault codes then turn Jog Dial to view error codes (Push
Start/Pause while the code is displayed to view the number of
cycles since the error occurred, Push Start/Pause to go back
to faults)
Peripheral (Main PCB) input Tests:
1. Select Extra Wash. Then turn the Jog-Dial so that the
Heavy Duty LED is turned on. Next, press the Start/Pause
Key. The Water Temperature will be displayed in Fahrenheit.
2. Select Extra Wash. Then turn the Jog-Dial so that the
Permanent Press LED is turned on. The door status will be
displayed (OP if open, CL if closed).
3. Select Extra Wash. Then turn the Jog-Dial so that the Sani-
tize LED is turned on. The door lock Switch status will be dis-
played (UL if unlocked, Lo if locked).
4. Select Extra Wash. Then turn the Jog-Dial so that the Bed-
ding Plus is turned on. The Water Frequency will be dis-
played.
IMPORTANT SAFETY NOTICE “For Technicians Only” This service data sheet is
intended for use by persons having electrical, electronic, and mechanical experience
and knowledge at a level generally considered acceptable in the appliance repair trade.
Any attempt to repair a major appliance may result in personal injury and property
damage. The manufacturer or seller cannot be responsible, nor assume any liability for
injury or damage of any kind arising from the use of this data sheet.
EEPROM Clear Check
Power off, Press Delay Start, Signal and Power Key at
the same time. Good = Good Fail = FAiL
All memory will be cleared, including Fault Codes