Salter 4 Way Timer & Clock Instructions For Use

Download Instructions for use of Salter 4 Way Timer & Clock Timer for Free or View it Online on All-Guides.com.

Brand: Salter

Category: Timer

Type: Instructions for use for Salter 4 Way Timer & Clock

Pages: 2

Download Salter 4 Way Timer & Clock Instructions for use

Salter 4 Way Timer & Clock Instructions for use - Page 1
1
Salter 4 Way Timer & Clock Instructions for use - Page 2
2
4 Way Timer & Clock
I
nstructions for use
TO SET CLOCK
1. PressClock button to select clock mode.
2. PressH to select a 12 or 24 hour clock.
3. Press and holdClock for 3 seconds. The digits will
begin to flash.
4
. PressH to set hours.PressM to set minutes.
PressS to set seconds. Press and hold the buttons
to advance the digits quickly.
5
. PressClock button again to confirm the time.
The battery compartment is located on the back of the
t
imer. Insert batteries (2 x LR44) observing the polarity
signs (+ and -) inside the battery compartment.
Replace cover.
TO SETTIMER
1. PressT1”,“T2”,“T3 orT4 corner button to
select a timer. T1”,T2”,“T3 orT4 will appear
o
n the LCD.
2. PressH to set hours.Press M to set minutes.
PressS to set seconds. Press and hold the buttons
to advance the digits quickly.
3. PressStart/Stop/Memory to start timer
c
ountdown.
4. PressStart/Stop/Memory again to pause or
resume timing.
5
. At00:00”, the alarm will sound for one minute. The
timer will start to count up. Each timer has its own
distinctive alarm.
6. PressStart/Stop/Memory to silence the alarm
and recall the last time set.
7. When the timer has stopped pressClear to reset
the timer to zero.
8. Multiple timers can be run by repeating steps 1-7
above.
9. Timers running in the background are indicated by
flashing T1,“T2,“T3 orT4 symbols on the
LCD. To view the countdown forT1 press the
T1 corner button (similar for T2,“T3 orT4”).
TO INSTALL BATTERIES
COUNT UP FEATURE
1. PressT1”,“T2”,“T3 orT4 corner button to
select a timer.
2. When the timer is displaying00:00 press
Start/Stop/Memory to start count up.
3. PressStart/Stop/Memory again to pause or
resume timing.
4. When the timer is stopped pressClear to reset
the timer to zero.
5. Multiple timers can be run by repeating steps
1-4 above.
USE AND CARE
If the display begins to disappear or alarm sounds faint,
replace batteries.Always remove flat batteries.
Do not place on or near hot surfaces.
Do not immerse in water.
To clean, simply wipe with a damp cloth.
GUARANTEE
This product is intended for domestic use only. Salter will
repair or replace the product,or any part of this product,
(excluding batteries) free of charge if within 2 years of the
date of purchase, it can be shown to have failed through
defective workmanship or materials. This guarantee
covers working parts that affect the function of the
product. It does not cover cosmetic deterioration
caused by fair wear and tear or damage caused by
accident or misuse. Opening or taking apart the product
or its components will void the guarantee. Claims under
guarantee must be supported by proof of purchase and
be returned carriage paid to Salter (or local Salter
appointed agent if outside the UK). Care should be taken
in packing the product so that it is not damaged while in
transit. This undertaking is in addition to a consumer's
statutory rights and does not affect those rights in any
way. For UK Sales and Service contact HoMedics Group
Ltd, PO Box 460,Tonbridge, Kent,TN9 9EW,UK.
HelplineTel No:(01732) 360783.Outside the UK contact
your local Salter appointed agent.
HoMedics Group Ltd
PO Box 460,Tonbridge, Kent,TN9 9EW, UK.
www.salterhousewares.co.uk REF: SL2093
E
GB
R
ÉGLER LE RÉVEIL
1
. Appuyer sur la touche « Clock » pour sélectionner
le mode horloge.
2. Appuyer sur « H » pour sélectionner l’horloge en 12
ou 24 heures.
3
. Maintenir appuyée la touche « Clock » pendant 3
s
econdes.Les chiffres se mettent à clignoter.
4
. Appuyer sur « H » pour régler l’heure.Appuyer sur
«
M » pour régler les minutes.Appuyer sur « S »
p
our régler les secondes. Maintenir appuyées les
t
ouches pour une avance rapide.
5
. Appuyer à nouveau sur la touche « Clock » pour
c
onfirmer l’heure.
Le compartiment batterie est situé à l’arrière du
minuteur. Insérer la pile (2 x LR44) en respectant le sens
des polarités (+ et -) indiq à l’intérieur du
compartiment batterie.Remettre le couvercle en place.
R
ÉGLER LE MINUTEUR
1
. Appuyer sur la touche « T1 »,« T2 »,« T3 » ou
«
T4 » pour sélectionner un minuteur. « T1 », « T2 »,
«
T3 » ou « T4 » s’affiche sur l’écran LCD.
2. Appuyer sur « H » pour gler l’heure.Appuyer sur «
M
» pour régler les minutes.Appuyer sur « S » pour
r
égler les secondes.Maintenir appuyées les touches
p
our une avance rapide.
3
. Appuyer sur « Start/Stop/Memory » pour lancer le
c
ompte à rebours du minuteur.
4
. Appuyer à nouveau sur « Start/Stop/Memory »
pour mettre en attente ou reprendre le comptage.
5. Arrivé à « 00:00 »,l’alarme sonne pendant une minute.
Le minuteur commence à compter les minutes.
Chaque minuteur possède sa propre sonnerie.
6. Appuyer sur « Start/Stop/Memory » pour arrêter
l
’alarme et revenir à l’heure prédemment glée.
7. Quand le minuteur est ar,appuyer sur « Clear »
pour le remettre à zéro.
8. Plusieurs minuteurs peuvent être programs en
tant les étapes 1 à 7 ci-dessus.
9. Les minuteurs fonctionnant en arrière-plan sont
signalés par les symboles « T1 »,« T2 »,« T3 » ou
« T4 » clignotant sur l’écran LCD. Pour voir le
compte pour « T1 », appuyer sur la touche « T1 »
(pareil pour « T2 »,« T3 » ou « T4 »).
INSTALLER LES PILES
FONCTION COMPTAGE PROGRESSIF
1. Appuyer sur la touche « T1 »,« T2 »,« T3 » ou
« T4 » pour lectionner un minuteur.
2. Quand le minuteur affiche « 00:00 », appuyer sur
« Start/Stop/Memory » pour lancer le compteur
progressif.
3. Appuyer à nouveau sur « Start/Stop/Memory »
pour mettre en attente ou reprendre le comptage.
4. Quand le minuteur est arrêté,appuyer sur « Clear »
pour le remettre à zéro.
5. Plusieurs minuteurs peuvent être programmés en
répétant les étapes 1 à 4 ci-dessus.
UTILISATION ET CONSIGNE
Si l’affichage commence à disparaître ou l’alarme
sonore à faiblir, remplacer les piles. Veillez toujours à
retirer les piles usagée.
Ne pas placer le chronomètre sur des sources de
chaleur ou à proximité de ces dernières.
Ne pas immerger le chronomètre dans l’eau.
Pour le nettoyer, il suffit de l’essuyer avec un
chiffon humide.
GARANTIE
Ce produit est uniquement destiné à un usage
domestique.Salter s’engage à réparer ou remplacer
gratuitement le produit, ou toute pièce de ce produit,
l’exclusion des piles) dans les 2 ans suivant la date d’achat
s’il est prouvé que la défaillance provient d’une mauvaise
qualité de fabrication ou de matériaux défectueux. Cette
garantie couvre les parties mobiles qui affectent le
fonctionnement du produit. Elle ne couvre pas toute
détérioration esthétique provoquée par l’usure normale
ou tout dommage provoqué par accident ou une
mauvaise utilisation.Le fait d’ouvrir ou de démonter le
produit ou ses composants annulera la garantie. Les
retours sous garantie doivent être accompagnés du
justificatif d’achat et expédiés en port pa à Salter (ou à
un agent Salter agréé local,si en dehors du R.-U.) Il est
conseil de bien emballer le produit afin de ne pas
l’endommager durant le transport. Cet engagement vient
en complément des droits statutaires du consommateur
et n’affecte ces droits en aucun cas.
Pour le service après-vente R.-U., contactez HoMedics
Group Ltd,PO Box 460,Tonbridge,Kent,TN9 9EW,R.-U.
AssistanceTél. : (01732) 360783. Hors R.-U.,contactez
votre agent agréé Salter HoMedics Group Ltd local.
F
1. ZurAuswahl des Uhrzeit-Modus dieTasteClock
drücken.
2. ZurAuswahl eines 12- oder 24-Stunden-FormatsH
drücken.
3. Den Knopf Clock 3 Sekunden gedrückt halten.
Die Uhrzeit wird nun blinken.
4. Zur Einstellung der StundenH drücken.Zur
Einstellung der Minuten M drücken.Zur Einstellung
der SekundenS drücken.Durch Gedrückthalten der
Tasten uft dieAnzeige schnell vor.
5. Die Uhrzeit durch erneutes Drücken derTaste
Clock bestätigen.
Das Batteriefach befindet sich auf der Rückseite des
Timers. Eine Batterie (2 x LR44) unter Beachtung der
Polarität (+ und -) in das Batteriefach einsetzen.Den
Deckel wieder anbringen.
TIMER EINSTELLEN
1. Die Ecktaste T1”,“T2”,“T3 oder T4 zurAuswahl
einesTimers drücken.Nun wird T1,“T2,“T3 bzw.
T4 auf der LCD-Anzeige eingeblendet.
2. Zur Einstellung der StundenH drücken.Zur
Einstellung der Minuten M drücken.Zur Einstellung
der SekundenS drücken.Durch Gedrückthalten der
Tasten uft dieAnzeige schnell vor.
3. Den Knopf Start/Stop/Memory drücken,um die
Rückwärtszählung zu starten.
4. DieTasteStart/Stop/Memory erneut drücken,um
die Zeithlung zu unterbrechen bzw. fortzusetzen.
5. Bei00:00 ertönt derAlarm eine Minute lang. Der
Timer beginnt nun mit derVorwärtszählung.Jeder
Timer hat einen anderen Alarm.
6. DieTaste Start/Stop/Memory drücken,um den
Alarmton auszuschalten und die zuletzt eingestellte
Zeit einzublenden.
7. Nach demTimer-Stopp mit derTasteClear den
Timer wieder auf Null stellen.
8. DurchWiederholung der Schritte 1-7 oben können
mehrere Timer in Betrieb gesetzt werden.
9. Im Hintergrund laufendeTimer werden durch die auf der
LCD-Anzeige blinkenden SymboleT1,“T2”,“T3 bzw.
T4 angegeben.ZurAnzeige desT1-Countdowns die
EcktasteT1 drücken.(FürT2,“T3 oderT4 muss
ebenfalls die jeweilige Ecktaste gedrückt werden.)
BATTERIEN EINLEGEN
VORWÄRTSZÄHLUNG
1. Die Ecktaste T1”,“T2”,“T3 oder T4 zurAuswahl
einesTimers drücken.
2. BeiTimeranzeige 00:00 den Knopf
Start/Stop/Memory drücken,dann beginnt die
Hochzählfunktion.
3. Den Knopf Start/Stop/Memory erneut drücken,um
die Hochzählung zu unterbrechen oder fortzusetzen.
4. Nach demTimer-Stopp mit derTasteClear den
Timer wieder auf Null stellen.
5. DurchWiederholung der Schritte 1-4 oben können
mehrere Timer in Betrieb gesetzt werden.
GEBRAUCH UND PFLEGE
Wenn dieAnzeige schlecht sichtbar wird oder der
Alarm nur leise ertönt,müssen die Batterien ersetzt
werden. Leere Batterien immer entfernen.
Nicht auf oder in die he von heißen Flächen stellen.
Nicht unterWasser tauchen.
Einfach mit einem feuchtenTuch reinigen.
GARANTIE
Dieses Produkt ist lediglich für den privaten Gebrauch
vorgesehen.Salter wird dieses Produkt bzw.einzelneTeile
dieses Produkts (außer Batterien) für eine Zeitdauer von
2 Jahren ab Kaufdatum kostenlos reparieren oder
ersetzen,wenn sich Defekte auf Material- oder
Herstellungsfehler zurückführen lassen.Diese Garantie
erstreckt sich auf Funktionsteile,die sich auf die Funktion
des Produkts auswirken.Ausgeschlossen von dieser
Garantie sind kosmetische Makel,die sich auf übliche
Abnutzungserscheinungen zurückführen lassen,sowie
durch Missgeschicke oder Missbrauch verursachte
Beschädigungen.Beim Öffnen oder Zerlegen des
Produkts oder einzelner Komponenten erlischt die
Garantie. Garantieanspche sind nur mit Kaufbeleg
möglich. Das Produkt in dem Fall bitte an Salter (oder
außerhalb Großbritanniens an einen Salter Fachhändler in
Ihrer Nähe) schicken (Fracht bezahlt).Das Produkt muss
so verpackt werden,dass es hrend desTransports
nicht beschädigt werden kann. Ihre gesetzlichen Rechte
werden durch diese Garantie nicht eingeschränkt.
Verkauf und Kundendienst, Großbritannien: HoMedics
Group Ltd,PO Box 460,Tonbridge,Kent,TN9 9EW,GB.
Helpline-Nummer:(01732) 360783. Setzen Sie sich
außerhalb Großbritanniens bitte mit Ihrem örtlichen
Salter HoMedics Group Ltd Fachhändler inVerbindung.
D
MINUTEUR RÉVEIL 4 MODES
Mode d’emploi
4
-FACH TIMER & UHR
Gebrauchsanleitung
RELOJ Y CRONÓMETRO DE 4
MODALIDADES
I
nstrucciones de uso
TIMER E OROLOGIO 4WAY
Istruzioni per l’uso
4-STANDEN TIMER EN KLOK
Gebruiksaanwijzing
TEMPORIZADOR E RELÓGIO
DE 4 MODOS
I
nstruções de Utilização
392
UHR EINSTELLEN
http://waterheatertimer.org/Woods-timers-and-manuals-old.html