• Home
• Brands
• Salus Manuals
• Salus VS10BR
• Salus VS20WRF Installer's/user's Manual

Salus VS20WRF Installer's/user's Manual

Download Installer's/user's manual of Salus VS10BR Thermostat for Free or View it Online on All-Guides.com. This version of Salus VS10BR Manual compatible with such list of devices, as: VS10BR, VS10WRF, VS20BRF, VS20WRF

1

2

4 in 1 Digital Thermostat RF

Models: VS20WRF and VS20BRF

VS10WRF and VS10BRF

INSTALLER / USER MANUAL

Product Compliance

This product complies with the essential requirements and other relevant provisions of Directives

2014/30/EU, 2014/53/EU and 2011/65/EU. The full text of the EU Declaration of Conformity is available at

the following internet address: www.saluslegal.com.

Safety Information

Use in accordance with the regulations.

Indoor use only.

Keep your device completely dry.

Disconnect your device before cleaning it with a dry cloth.

Introduction

Thank you for purchasing the SALUS 4 in 1 room thermostat it must be used with the Universal Gateway

UGE600 (purchased separately) when having an Internet connection or with the KL08RF for the underfloor

system withoul Internet connection. The Universal Gateway allows communication with other devices in

the iT600 RF system range. Other Zigbee devices include wiring centre, system receiver & TRV. You can

use your iT600 system with the Salus Smart HomeApp. Available on Google Play and App Store.

Always isolate the AC Mains supply before installing or working on any components that require 230 VAC 50Hz supply.

RX10RF (optional for an underfloor

system, mandatory for a TRV system)

TRV10RFM

TRV10RF

KL10RF

KL08RF

Installation – Terminal Connections VS10WRF

Understanding your terminal connections

Rear of unit

Power Terminals 230 Vac

Used for supplying power to

the unit. 230V supply can be

sourced from the wiring centre

or any convenient source.

Sensor Terminals

Can be used for external AIR,

Floor sensor when configured

as thermostat. Can also be used

for Cylinder thermostat when

configured for HW.

1

2

1

2

Pairing with Wiring Center (KL08RF) with Internet connection

6

8

10

7

9

11

5 sec

SALUS Controls plc

SALUS House

Dodworth Business Park South,

Whinby Road, Dodworth,

Barnsley S75 3SP, UK.

Sales: T: +44 (0) 1226 323961

E: [email protected]

Technical: T: +44 (0) 1226 323961

E: [email protected]

www.salus-controls.com

SALUS Controls is a member of the Computime Group

Maintaining a policy of continuous product development, SALUS Controls plc

reserves the right to change specification, design and materials of products listed in

this brochure without prior notice.

12

Installation – First Power Up

The following screens show examples only

MCU software version

will be shown

ZIGBEE software version

will be shown

Please make sure that your Universal Gateway is installed. You can use it with both internet and non internet connection.

The LED will be blue when connected to the internet and red when it’s not connected.

With Internet

Without Internet

*Please note that 88.8 and

8.8 are a reference to the

software version.

If you are installing an underfloor system without an Internet connection, you can use the coordinator from the

KL08RF instead of the Universal Gateway.

Pairing with Wiring Center (KL08RF) with Internet connection

3

1

2

Pairing with Wiring Center (KL08RF) without Internet connection

OR

5 sec

1

2

Pairing the TRV with Internet connection

31 2

4

5

Tap Scan for equipment when you

want to start adding equipment

to the App. The gateway will start

flashing red.

3

5

4

6

7

OR

5 sec

5 sec

5

Tap Scan for equipment when you

want to start adding equipment

to the App. The gateway will start

flashing red.

4

CO10RF

6

7

Press and hold the for

10 seconds until the TRV starts

flashing red.

Wait until the LED is solid red.

Press the Open/Close button

once. When the initialization

process is complete, the LED will

go off.

8 9

10

11

12

Installation – Power Up your devices

Please follow the installation procedure for all equipment. After installation, your devices should look like this:

Please follow the on screen instruction in order to complete the pairing process.