• Home
• Brands
• Canon Manuals
• Canon iP6600D - PIXMA Color Inkjet Printer
• Canon PIXMA iP6600D Start Here

Canon PIXMA iP6600D Start Here

Download Start here of Canon iP6600D - PIXMA Color Inkjet Printer All in One Printer, Digital Camera for Free or View it Online on All-Guides.com.

1

2

Start Here

Easy Setup Instructions

1 Unpack the Printer

Carefully remove all items from the box.

Power Cord

PIXMA iP6600D

Print Head

Documentation and

Software Kit

PIXMA iP6600D

Photo Printer

1

2 Prepare the Printer

Before turning on the printer, open the cover

and remove the protective material and tape

from the printer as shown.

The tape position is subject to change. Write

down the serial number located inside the

printer. You will need this to register your

products.

CAUTION: Be sure to remove the protective

material before you turn on the printer.

Close the cover. Plug the power cord into the

back of the printer and connect the other end

to a power outlet. Press the POWER button.

The printer will initialize. Wait until the

POWER lamp displays a steady light.

NOTE: Do not connect the USB cable at this

stage.

When the screen shown on the LCD appears,

use the buttons to select a language

and then press the OK button.

NOTE: If you leave the printer more than five

minutes without using any button on the

operation panel, the LCD goes into sleep

mode automatically. Press the OK button to

turn on the LCD again.

Pull down the paper output tray. Raise the

cover. Lower the inner cover.

NOTE: Putyour fingers in the notches in

either side of the paper output tray and pull

down to open it.

The print head holder automatically moves to

the center.

IMPORTANT: If the cover is left open for more

than ten minutes, the print head holder

moves to the right. Close and reopen the

cover to return the holder to the center.

5

4

3

2

1

3 Install the Print Head

Remove the print head from its package.

CAUTION: There might be some transparent

or light blue ink on the inside of the bag the

print head comes in, or the inside of the

protective cap. This has no effect on print

quality. Be careful not to get ink on yourself

when handling these items.

Remove the orange protective cap from the

print head.

NOTE: Do not touch the print head nozzles

and the electrical contacts.

Firmly raise the print head lock lever until it

stops into place.

Slide the print head into the holder.

The print head will rest at a slight angle.

Lower the print head lock lever carefully and

press it down.

5

4

3

2

1

4 Install the Ink Tanks

Peel back the orange tab completely and

remove the plastic wrapper from the Yellow

Ink Tank (CLI-8Y).

Twist off and discard the orange protective

cap located on the bottom of the ink tank.

IMPORTANT: Do not touch the electrical

contacts.

NOTE: To avoid spilling ink, never press on

the sides of an ink tank. Do not touch the

open ink port once the protective cap is

removed, as this may prevent the ink from

being ejected properly.

Insert the yellow ink tank into the right-hand

slot.

Press the mark on the ink tank until it

clicks into place and then its lamp lights red.

Insert the remaining five ink tanks into their

appropriate slots. Ensure that ink tank lamps

light red.

Close the inner cover and then the cover. The

message requesting head alignment is

displayed on the LCD. Go to the next step.

NOTE:

· The printer will perform a print head cleaning.

Wait until the POWER lamp displays a steady

light before proceeding.

·Ifthe Alarm lamp still lights even after the

printer has stopped making operating noises,

an ink tank may not be installed properly. Open

the cover and make sure that the ink tanks are

installed in the correct order directed on the

label.

5

4

3

2

1

5 Align the Print Head

Lift open the paper support and extend the

paper output tray.

IMPORTANT: Be sure to close the inner cover

completely, or the paper will not feed properly.

Pinch the paper guide and slide it to the left.

Load a few sheets of blank paper into the auto

sheet feeder, align the paper with the right

side of the cover guide, then slide the paper

guide toward the left edge of the paper.

Ensure that the message requesting head

alignment is displayed on the LCD, select Yes

using the buttons and then press the OK

button.

The pattern is printed. And the print head is

aligned automatically.

IMPORTANT: It takes about 3 minutes and 30

seconds to finish printing.

When automatic print head alignment cannot

be executed correctly, the message "Auto head

align has failed. Press [OK] and repeat

operation. <See manual>" is displayed on the

LCD.

Refer to "An Error Message is Displayed on the

LCD" in the

Direct Printing Guide

.

3

2

1

Inner cover

Cover

Paper output tray

Tear at notch to open

Print head

nozzles

Electrical

contacts

Protective cap

Auto sheet

feeder

Paper

guide

Continue with Step 6

on side two.

Paper output tray

Paper support

Refer to the color

guide on the print

head lock lever.

POWER button

POWER lamp

CLI-8C Cyan

CLI-8BK Black

CLI-8PC Photo Cyan

Electrical contacts

Ink tank lamp

Print side

Cover guide

click

Ink Tanks

CLI-8M Magenta

CLI-8PM Photo Magenta

CLI-8Y Yellow

Series

Photo Printer

Ink port

Serial number location

iP6600_ESI_US_V1.qxd 05.5.26 7:10 PM ページ1