Danfoss RT 30AW Installation Manual

Download Installation manual of Danfoss RT 112W Switch for Free or View it Online on All-Guides.com. This version of Danfoss RT 112W Manual compatible with such list of devices, as: RT 19W, RT 30AB, RT 31B, RT 32B, RT19S

Danfoss RT 112W Installation manual - Page 1
1
Danfoss RT 112W Installation manual - Page 2
2
Installation guide
Pressure switch
RT 19W, RT19B, RT19S, RT 30AW, RT 30AB, RT 30AS, RT 31W, RT 31B,
RT 31S, RT 32W, RT 32B, RT 33B, RT 35W, RT 112W
017R9326
017R9326
© Danfoss | DCS (jmn) | 2015.11
IC.PI.P10.S2.51 | 520B6749 | 1
PED approved acc. to EN12953-9 and EN12922-11
5
9
38
Fig. 2
Fig. 3
Danfoss
17-660-15
Fig. 1
Danfos
s
17-5027.10
Fig. 4 Fig. 5
ENGLISH
Fail safe pressure switches types:
RT 19W, RT 19B, RT 19S, RT 30AW, RT 30AB,
RT 30AS, RT 31W, RT 31B, RT 31S, RT 32W,
RT 32B, RT 33B, RT 35W, RT 112W
Data
Tested and approved by TÜV
(Technischer Überwachungs Verein)
The meaning of the type designation
letters is as follows:
A:
Also approved for use in refrigeration plant
W:
Pressure monitoring with automatic reset
B: Pressure limiter with external reset
S:
Safety pressure limiter with internal reset
Contact load: see fig.3
Max. ambient temperature: -40 °C 70 °C
Max. temperature of medium: 150 °C
Max. test pressure:
RT 19, RT 32 (-W -B -S): 47 bare
RT 30A, RT 31 (-W -B -S): 25 bare
RT 33B, RT 35W, RT 112: 8 bare
Min. test pressure: - 1 bar
Installation
A set of Pg13.5 cable gland is attached to
the RT in a separate bag. To ensure IP66
(units with automatic reset) or IP54 (units
with external reset) grade of RT enclosure
it is necessary to assemble this gland as
shown in the fig. 4. If this gland is not used
with a cable, a metal blinding should be
also assembled.
Make the pressure connection so that any
impurities in the line do not block the
pressure inlet of the control.
For example, fit the pressure switch to an
upright connector (with the unit verti-
cal). Damp strong pressure pulsations.
A damping loop will often be sufficient.
Insert a water-filled loop as a temperature
barrier; a 10 mm Cu tube, for example, if
in a high temperature plant there is a risk
of the pressure connection to the control
becoming heated to more than 100 °C.
In water plant, position the pressure
switch so that it cannot be exposed to
frost (let it operate on an air cushion, for
example).
Setting
The pressure switch must be set to provide
the function - make or break - on rising
temperature (for RT 31, RT 32 and RT 33
on fal
ling temperature). The setting can be
made
with the setting knob (5) while at the
same
time reading off the main scale (9).
See fig. 1.
The differential must be set with
the differential setting disc (19) using the
nomogram in fig. 2.
Examples
1. RT 31W
The pressure on a steam boiler must be
controlled by an RT 31W.
Max. pressure 8 bar, min. pressure 7.5 bar,
differential 8-7.5 = 0.5 bar
1. Connect the oil burner to pressure
control terminals 1-2
2. Using the setting knob (5), set the
pressure control at 8 bar
3. Set the differential disc at approx. 3.5 in
accordance with the nomogram in fig. 2.
2. RT 19B or RT 19S
When the pressure in a boiler exceeds
20 bar, the RT 19 must cut off the burner.
Automatic restart must not occur.