DeLOCK 86441 User Manual
Download Operation & user’s manual of DeLOCK 86441 Media Converter for Free or View it Online on All-Guides.com.
Brand: DeLOCK
Category: Media Converter
Type: Operation & user’s manual
Model: DeLOCK 86441 , DeLOCK 86442
Pages: 2
1
2
86441
Media Converter 1000Base-LX SC SM
1310 nm 10 km compact
86442
Media Converter 1000Base-SX SC MM
850 nm 550 m compact
Product-No:86441-86442
User manual no:86441-a
www.delock.com
User manual
Gebrauchsanweisung
LED description
LED indicator lamps serve as device monitoring and troubleshooting
display. The following is the explanation for each LED indicator lamp.
Fig. 1: Front panel
LED Status Description
PWR/STA Green Lit when power is available
TP
Green Lit when TP cable connection with remote de-
F/O
Orange Lit when Fiber cable connection at 1000M with
remote device is good.
FDX
Green Lit when TP works in Full-Duplex.
Not-Lit when TP works in Half-Duplex.
SPD
Green Lit when TP works in 10M.
Lit when TP works in 100M.
Orange Lit when TP works in 1000M.
DIP SWITCH Setting
The default setting for PIN 1 through 7 is ON. The PIN 8 is OFF.
Pin no. Function OFF ON
1 TP Auto-Negotiation Disable Enable
2 Manual TP speed 10M 100M
3 Manual TP speed N/A 1000M
4 N/A N/A N/A
5 N/A N/A N/A
6 F/O mode Force Auto
7 N/A N/A N/A
8 Link Alarm Disable Enable
NOTE:
1. Before changing TP speed, please make sure PIN 1 is set to OFF.
2. When TP speed is set to 10M or 100M manually, PIN 3 needs to be
turned OFF.
3. Under 1000Mbps, it supports full-duplex mode only.
-
3
-
Description
The Delock Gigabit Ethernet Media Converter series is designed to
extend a copper based Ethernet network via fiber cable. The
10/100/1000 Mb/s Gigabit Ethernet Media Converter series is fully
compliant with IEEE802.3z and IEEE802.3ab standards. The installation
and operation procedures are simple and straightforward. Operation
status can be locally monitored through a set of diagnostic LEDs located
in the front panel.
Package content
• Media converter, power supply, user manual
Safety instructions:
1. This product is suitable for indoor application only.
2.
3.
Function Description
Standard protocol IEEE802.3 10/100Base-TX
IEEE802.3z 1000Base-SX/LX
IEEE 802.3ab 1000Base-T
Connector one RJ-45 connector
one SFP slot
TP cable Cat.5 UTP cable or better
Operation mode full duplex mode or half duplex mode
Auto MDI/MDI-X support on RJ45 port
Data rate Fiber: 1000 Mb/s
Copper: 10/100/1000 Mb/s
Power supply +3.3 V DC 2 A
Environmental
temperature
0 °C ~ 50 °C
Relative humidity 5 % ~ 90 %, non-condensing
Dimensions ca. 74 mm x 51 mm x 20 mm
Installation
• Fiber interface
be paired at both ends.
• TP interface
Connect a TP cable from the 10/100/1000Base-T network to the RJ-45
port on the media converter.
• Power
Connect the power adapter to the media converter and check that the
PWR/STA LED lights up. The TP and F/O LEDs will light up when all the
cable connections are correctly installed.
-
2
-