Carvin BX500 Operating Manual

Download Operating manual of CARVIN BR510 Amplifier for Free or View it Online on All-Guides.com.

Brand: CARVIN

Category: Amplifier

Type: Operating manual

Model: CARVIN BR510 , CARVIN BR515 , CARVIN BX500

Pages: 2

Download CARVIN BR510 Operating manual

CARVIN BR510 Operating manual - Page 1
1
CARVIN BR510 Operating manual - Page 2
2
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
SAFETY INSTRUCTIONS (EUROPEAN)
The conductors in the AC power cord are colored in accordance with the following code.
GREEN & YELLOW—Earth BLUE—Neutral BROWN—Live
U.K. MAIN PLUG WARNING: A molded main plug that has been cut off from the cord is
unsafe. NEVER UNDER ANY CIRCUMSTANCES SHOULD YOU INSERT A DAMAGED
OR CUT MAIN PLUG INTO A POWER SOCKET.
IMPORTANT! FOR YOUR PROTECTION, PLEASE READ THE FOLLOWING:
WATER AND MOISTURE: Appliance should not be used near water (near a bathtub, washbowl,
kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc). Care should be taken
so that objects do not fall and liquids are not spilled into the enclosure through openings.
POWER SOURCES: The product should be connected to a power supply only of the type
described in the operating instructions or as marked on the appliance.
GROUNDING OR POLARIZATION: Precautions should be taken so that the grounding or
polarization is not defeated.
POWER CORD PROTECTION: Power supply cords should be routed so that they are not likely
to be walked on or pinched by items placed upon or against them, paying particular attention to
cords at plugs, The appliance inlet is the disconnect device. Keep it readily accesable.
SERVICING: The user should not attempt to service the appliance beyond that described in the
operating instructions. All other servicing should be referred to qualified service personnel.
FUSING: If your unit is equipped with a fuse receptacle, replace only with the same type fuse.
Refer to replacement text on the unit for correct fuse type.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL! THIS UNIT CONTAINS HIGH
VOLTAGE INSIDE!
CAUTION
RISK OF ELECTRIC SHOCK
This symbol is intended to
alert the user to the pres-
ence of uninsulated “dan-
gerous voltage” within the
product’s enclosure that
may be of sufficient magnitude to con-
stitute a risk of electric shock to persons.
This symbol is
intended to alert the
user to the presence
of important operating
and maintenance (ser-
vicing) instructions in the literature
accompanying the appliance.
RISK OF ELECTRIC SHOCK
DO NOTOPEN
CARVIN ENGINEERING DATA
OPERATING MANUAL
76-45501B 0812
LIMITED WARRANTY
Your Carvin product is guaranteed against failure for 1 YEAR unless otherwise stated.
Carvin will service and supply all parts at no charge to the customer providing the unit
is under warranty. Shipping costs are the responsibility of the customer. CARVIN
DOES NOT PAY FOR PARTS OR SERVICING OTHER THAN OUR OWN. A COPY OF
THE ORIGINAL INVOICE IS REQUIRED TO VERIFY YOUR WARRANTY. Carvin assumes
no responsibility for horn drivers or speakers damaged by this unit. This warranty
does not cover, and no liability is assumed, for damage due to: natural disasters, acci-
dents, abuse, loss of parts, lack of reasonable care, incorrect use, or failure to follow
instructions. This warranty is in lieu of all other warranties, expressed or implied. No
representative or person is authorized to represent or assume for Carvin any liability
in connection with the sale or servicing of Carvin products.
CARVIN SHALL NOT BE
LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
MAINTAINING YOUR EQUIPMENT
Avoid spilling liquids or allowing any other foreign matter inside the unit. The panel
of your unit can be wiped with a dry or slightly damp cloth in order to remove dust
and bring back the new look.
As with all pro gear, avoid prolonged use in caustic
environments (salt air). When used in such an environment, be sure the amplifier is
adequately protected.
SERVICE
In the USA go to www.carvinservice.com.
Outside the USA, contact your dealer or go to http://www.carvinworld.com for your
nearest service center. Include a written description of the problem with serial number
and date of purchase.
The BX Series Bass Amplifier Heads offer classic natural bass tone with unprecedented tonal
control and extended headroom. The BX500 delivers 300w at 8 ohms and 500w at 4ohms or
2ohms, yet weighs in at only 5 pounds.
Four discrete Class A input stages produce the harmonic basis for the preamp right from the
input jack. It begins with a boutique flat response, then we add extensive tone control allowing
you to carve out your signature sound. Harmonic content increases as you turn up the DRIVE
control producing rich harmonics at maximum settings. The BX500 also features 12AX7 preamp
tube (bypassable) to add further warmth to your sound. The CLASS-D output and lightweight
switch-mode power supply use far less energy from the wall while producing less heat.
Light weight, solid design, bullet-proof construction and a list of indispensable features assure
the BX500 will be the heart of your rig for years to come.
•DiscreteCLASSAinputstages
•PreampDRIVEandMASTERvolumecontrols
•2midsweepsemi-parametricEQ,BASSandTREBLE
•Switchable9-bandGraphicEQwithfrontpanelswitchorbytheoptionalFS22footswitch
•SingleknobCOMPRESSOR
•EffectLoop
•Warm12AX7preamptubewithbypassswitch
•SwitchableMUTEfrontpanelswitchorbytheoptionalFS22footswitch
•DIRECTOUTbalancedXLRwithfrontpanelLEVELcontrol-workswithMUTEswitch
•SwitchableGroundLiftforDCisolation
•TUNERoutputjackindependentofMUTEswitch
•HighcurrentSPEAKON
®
combo connectors also accept 1/4” jacks.
•CLASS-Damplifierrunscoolwhileconsuminglesspower
•Variablespeedfan,silentrunningatlowspeed.
•Solidmetalshaftcontrolswiththreadedmetalbushingsmountedtofrontpanel
•CircuitboardsareMILSPEC,doublesided,FR-4glassepoxy
•Energyefficientworldwidepowersupplyaccepts90-250VAC,50-60Hz
•Compactandlightweightunder6lbs.
•DesignedandmanufacturedbyCarvinintheUSA
GETTING STARTED
1. With POWER off, connect a speaker cabinet to one of the rear SPEAKER OUTPUTs.
2. Set the DRIVE and MASTER volume to “0” and set the ACTIVE INPUT switch for your type
of bass.
3. Set the four tone controls to their center “0” position and the CONTOUR to FLAT. This is
the “FLAT” setting for the amp. For now, turn off the graphic EQ.
4. Now, turn the amp ON. Turn up the volume on your bass guitar. Gradually increase the
MASTER control to the desired level. If no sound is heard turn down the MASTER, check the
MUTE switch, speaker connections, and PROTECT LED.
5. Increasing the DRIVE control will add harmonic richness to your sound. Turning up the
DRIVE also increases volume. Re-adjust the MASTER volume after adjusting the DRIVE.
6.Adjustthetonecontrolstoyourliking.Keepinmindthatturningupatonecontrolisn’talways
the answer. Sometimes turning down one of the MID controls will get you the sound you want.
7. Need more volume? There is a limit to the amount of volume a speaker can produce and
driving a speaker beyond it’s limit can damage it. Even though these are powerful amplifiers,
adding more speakers is the only way for substantially more output. Every time you double
your speakers, you increase your acoustic output by a factor of four.
Hopefully, this will help you get started. Have fun exploring the features and sounds of the
BX500. Take the time with your new amp to realize it’s full potential.
BX500 / BR510 / BR515 / BASS AMPLIFIERS
RECEIVING INSPECTION—read before getting started
INSPECT YOUR UNIT FOR DAMAGE which may have occurred during shipping. If damage
is found, please notify the shipping company and CARVIN immediately.
SAVE THE CARTON & ALL PACKING MATERIALS. In the event you have to re-ship your
unit, always use the original carton and packing material. This will provide the best possible
protection during shipment. CARVIN and the shipping company are not liable for any damage
caused by improper packing.
SAVE YOUR INVOICE. It will be required for warranty service if needed in the future.
SHIPMENT SHORTAGE. If you find items missing, they may have been shipped separately.
Please allow several days for the rest of your order to arrive before inquiring.
RECORD THE SERIAL NUMBER on the enclosed warranty card for your records. Keep your
portion of the card and return the portion with your name and comments to us.
USA customers register online at: www.carvin.com/registration
All other countries register online at: www.carvinworld.com/registration
SPECIFICATIONS:
Output Power
8ohms, THD <1.0% 300w
4ohms, THD <1.0% 500w
2ohms, THD <1.0% 500w (2 ohm switch engaged)
BR510 & BR515: Enclosure impedance 8 Ohms
Input Impedance: >200K
Tone Controls: TREBLE 10K, BASS 50Hz , 2 semi-parametric
MIDs, CONTOUR, and 9-band Graphic EQ
Drive Control: Varies input gain and harmonic content
AC Requirements: 90to250VAC50/60Hz
Power Requirements: 500VA
Dimensions
BX500: 3.25”H (with feet) x14.0”Wx8.25”D
BR510N & BR515N: 23.8”Hx20.7”Wx18.5”D
Weight : BX500:under6lbs.net(2.72kgs)
BR510:57.5lbs.(26kgs)BR515:56lbsnet(25.4kgs)
Warranty: One year parts and labor
Optional Accessories: FS22 footswitch
BX500RP rackmount faceplate kit w/handles
CV615 vinyl cover for BR510 or BR515
Helpful Hints
1) No sound:
The MUTE function has been inadvertently engaged.
Speakers have been improperly connected.
Effect Loop has been improperly connected.
2) No High Frequencies: (BR510, BR515 and external cabinets)
The HIGH FREQUENCY ATTENUATION control is set low or OFF.
The HF driver may have been damaged from too much power or distortion.
3) AMP seems very sensitive on input signals:
The drive control is turned all the way up.
The active switch may need to be turned on.
4) DIR XLR hum:
Try switching the rear GND LIFT switch IN or OUT.
Check for noise from external effects or bad cabling.
5) POOR BASS FROM MULTIPLE ENCLOSURES:
Make sure the internal speaker wiring of each cabinet is correct for phase ( +/- ).
6) FOR MAXIMUM OUTPUT:
To get more output, use multiple speakers or enclosures. Every time you double your speakers, your acoustic output goes up by a factor of four.
Load the amplifier down to its lowest minimum impedance for maximum RMS power.
* If you are using less than 4 ohms, be sure to set the 2 OHM SWITCH on the back of the BX500. If you go below the minimum load, your amp will shut off and go into the “protect” mode.
To reset, turn your amp off and connect the recommended load or set the 2 OHM SWITCH.
SPEAKON
®
cables are recommended for your BX500 because of their high current capacity. While standard 1/4” speaker cables will work, 12 GA SPEAKON
®
cables will allow higher
currents to pass through the cable to extract every watt from your amp.
The BX500 is a powerful amplifier. As with any amplifier, make sure your speakers are suitable for the available wattage. Driving speakers with too much wattage will cause them to distort
and eventually fail. If distorted sound is coming from the speakers, reduce the volume until the distortion stops.
BX500
BR510
BR515
MADE IN
USA
RISK OF ELECTRIC SHOCK
DO NOTOPEN
carvin.com 800-854-2235