• Home
• Brands
• CARVIN Manuals
• CARVIN UX1000BP
• CARVIN UX1000BP Manual

CARVIN UX1000BP Manual

Download Operating manual of CARVIN UX1000BP Other for Free or View it Online on All-Guides.com.

1

2

3

4

This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this

device does not cause harmful interference. This device complies with INDUSTRY

CANADA R.S.S. 210, en conformite´ avec IC: RSS-210/CNR210.

CAUTION! Electrical shock can result from removal of the receiver cover. Refer servicing to qualified

service personnel. No user-serviceable parts inside. Do not expose to rain or moisture. The circuits

inside the receiver and transmitter have been precisely adjusted for optimum performance and compli-

ance with federal regulations. Do not attempt to open the receiver or transmitter. To do so will void the

warranty, and may cause improper operation.

REGULATIONS AND SERVICING

1. Use only fresh alkaline batteries. Replace batteries with every 25 hours of use.

2. Position the receiver so that it has the fewest possible obstruction between it

and the normal location of the transmitter. Line-of-sight is best.

3. The transmitter and receiver should be as close together as conveniently possible.

4. The receiver antenna should be in the open and away from any metal or cement walls. If in

a rack, have the unit on top or angle antennas outward away from the metal rack.

5. Turn the transmitter off when not in use. Remove the battery if the transmitter is

not used for a period of time.

TIPS TO OBTAIN THE BEST WIRELESS RESULTS

PROGRAMMING HAND HELD MIC CONT.

2. SETTING FREQUENCY

FREQUENCY DISPLAYED

Press "SET" for three seconds for the "MHZ" to show on the LCD. Press "UP" or "DOWN" to

increase or decrease the frequency. Re-press "SET" again and the mic will store the frequency.

GROUP DISPLAYED

Press "SET" for three seconds for the Group digit to show. Then re-press "SET" and the fre-

quency starts flashing. Press "SET" a third time until the "MHZ" show up. Press "UP" or "DOWN"

to increase or decrease Group digit. Press "SET" again and the mic will store the frequency.

3. SETTING SENSITIVITY

FREQUENCY DISPLAYED

Press "SET" for three seconds for the "MHZ" to show on the LCD. Press "SET"

again and the Group digit starts flashing. Press "SET" a third time and the frequency starts

flashing. Press "SET" once more to display the sensitivity setting.

GROUP DISPLAYED

Press "SET" for three seconds for the Group digit display. Re-press "SET" and the frequency

starts flashing. Press "SET" button again until "MHZ" shows. Press "SET" again until sensi-

tivity displays. Press "UP" or "DOWN" button to increase or decrease sensitivity. There are 4

sensitivity could be adjusted : 0dB, -6dB, -12dB, -24dB

4. SETTING LOCK-ON

FREQUENCY DISPLAYED

Press "SET" for three seconds until "MHZ" shows on the LCD. Press "SET" again and the Group

digit starts flashing. Press "SET" again until the frequency starts flashing. Push "SET" button

again and the sensitivity displays. Hiting "SET" once more turns on the “LOCK-ON” setting.

Press "UP" button for “LOCK-ON” mode and "DOWN" button for “LOCK-OFF” mode. Re-press

"SET" and the lock function will store.

GROUP DISPLAYED

Press "SET" for three seconds for the Group digit display. Re-press "SET" and the frequency

starts flashing. Press "SET" button again until "MHZ" shows. Press "SET" again to display the

sensitivity. Press "SET" until "LOCK OFF" starts flashing. Press "UP" for LOCK-ON mode and

"DOWN" button for LOCK-OFF mode. Push "SET" to store the lock function.

5. RELIEVED LOCK-ON

Press "SET" for three seconds till "LOCK ON" displays, then press "DOWN" and "SET" at the

same time to store LOCK-ON relieved.

6. Pressing any button will display "LOCK ON" during Lock On mode. This setting remains

until it is disabled. Turning the unit off will not disable the Lock On mode.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

SAFETY INSTRUCTIONS (EUROPEAN)

The conductors in the AC power cord are colored in accordance with the following code.

GREEN & YELLOW—Earth BLUE—Neutral BROWN—Live

U.K. MAIN PLUG WARNING: A molded main plug that has been cut off from the cord is

unsafe. NEVER UNDER ANY CIRCUMSTANCES SHOULD YOU INSERT A DAMAGED

OR CUT MAIN PLUG INTO A POWER SOCKET.

IMPORTANT! FOR YOUR PROTECTION, PLEASE READ THE FOLLOWING:

WATER AND MOISTURE: Appliance should not be used near water (near a bathtub, washbowl,

kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc). Care should be taken

so that objects do not fall and liquids are not spilled into the enclosure through openings.

POWER SOURCES: The appliance should be connected to a power supply only of the type described

in the operating instructions or as marked on the appliance.

GROUNDING OR POLARIZATION: Precautions should be taken so that the grounding or polar-

ization means of an appliance is not defeated.

POWER CORD PROTECTION: Power supply cords should be routed so that they are not likely

to be walked on or pinched by items placed upon or against them, paying particular attention

to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

SERVICING: The user should not attempt to service the appliance beyond that described in the

operating instructions. All other servicing should be referred to qualified service personnel. If

your unit is equipped with a fuse receptacle, replace only with the same type fuse. Refer to replace-

ment text on the unit for correct fuse type.

This symbol is intended to

alert the user to the pres-

ence of uninsulated “dan-

gerous voltage” within the

product’s enclosure that may be of suf-

ficient magnitude to constitute a risk of

electric shock to persons.

This symbol is

intended to alert the

user to the presence of

important operating

and maintenance (servicing) instruc-

tions in the literature accompanying

the appliance.

LIMITED WARRANTY

90 days on all wireless electronic components. Does not cover cables, connectors, or broken parts

caused by normal ware and tear or dropping. Shipping costs are the responsibility of the customer.

CARVIN DOES NOT PAY FOR PARTS OR SERVICING OTHER THAN OUR OWN. A COPY OF THE ORIG-

INAL INVOICE IS REQUIRED TO VERIFY YOUR WARRANTY. Carvin assumes no responsibility for horn

drivers or speakers damaged by this unit. This warranty does not cover, and no liability is assumed,

for damage due to: natural disasters, accidents, abuse, loss of parts, lack of reasonable care, incor-

rect use, or failure to follow instructions. This warranty is in lieu of all other warranties, expressed or

implied. No representative or person is authorized to represent or assume for Carvin any liability in

connection with the sale or servicing of Carvin products. CARVIN SHALL NOT BE LIABLE FOR INCI-

DENTAL OR CONSEQUENTIAL DAMAGES.

When RETURNING merchandise to the factory, you may call for a return authorization number. Describe

in writing each problem. If your unit is out of warranty, you will be charged the current FLAT RATE for

parts and labor to bring your unit up to factory specifications.

HELP SECTION

RF Interference

If you encounter receiving interference (from other than an operating TV station), often it can be

eliminated by adjusting the receiver’s antenna.

Please note that wireless frequencies are shared with other audio services. According to Federal

Communications Commission regulations, “Wireless microphone operations are unprotected from

interference from other licensed operations within the band. If any interference is received by any

Government operation, the wireless microphone must cease operation…”