Extron Electronics EBP 1200C Setup Manual
Download Setup manual of Extron electronics EBP 1200C Enclosure for Free or View it Online on All-Guides.com.
Brand: Extron electronics
Category: Enclosure
Type: Setup manual for Extron electronics EBP 1200C
Pages: 14
1
2
3
4
5
6
7
8
9
10
11
12
13
14
1
Product Category
IMPORTANT:
Go to www.extron.com for the
complete user guide and installation
instructions befor
e connecting the
pr
oduct to the power sou
rce.
EBP 1200C Cable Cubby Enclosure
with eBUS
®
Button Panel • Setup Guide
The Extron EBP1200C is a Cable Cubby
®
1200 with an
integrated eBUS button panel to combine convenient
AV and data connectivity with a fully customizable AV
system control interface for use with Extron IPCPPro
Series Control Processors.
NOTE: These products are only for use with Extron
UL Listed IPCP Pro control processors.
This guide provides basic instructions for an
experienced installer to install an EBP1200C Cable
Cubby button panel:
• Setup Checklist
• Installing the EBP 1200C Cable Cubby
• Connecting to the eBUS System
For more details on eBUS, see the eBUS Technology
Reference Guide, available on www.extron.com. For
details on conguration, see the software help les.
HDMI HDMI3
HDMI4
21 CONFIGURABLE
100-240V ~ --A MAX
50-60 Hz
AUDIOOUTPUT
TALLY OUT
CONTACT IN
L
12
R
LR
Tx Rx G
3214+V
1234G
RS-232
OUT
IN
HDMI
INPUT REMOTE
POWER
12V
--A MAX
G
Tx Rx RTSCTS
COM 1
G
Tx Rx
COM 2
VCG
VOL
RELAYS
1 2 C
1 2 3 4 G
DIGITAL I/O
PWR OUT = 6W
eBUS
+V+S
-S
G
LAN
IPCP PRO 250
IR/S
S G
Display with Speakers
Ethernet
TCP/IP
Network
Extron
IN1604 HD
Four Input Scaler
Extron
IPCP Pro 250
IP Link Pro
Control Processor
Extron
EBP 1200C
Cable Cubby eBUS
Button Panel
Laptop Laptop
OFF
ON
LAPTOP
PC
MUTE
VGA
HDMI
AUX VIDEO
Extron
HDMI
eBUS
HDMI
HDMI
Computer
MODEL 80
FLAT PANEL
Ethernet
RS-232
VGA
Figure 1. EBP 1200C Application Diagram
Setup Checklist
Step 1 — Planning
Download and install the latest version of the software, rmware, and device drivers needed to congure the IPCPPro
and control the connected AV products. See the IPCPPro Series User Guide (available at www.extron.com) for details on
software and drivers.
Obtain network information (IP addresses, passwords, DHCP settings, and the like) and the MAC address for the control
processor.
Obtain model names, drivers, and setup information for AV devices.
Determine which eBUS cabling topologies to use and obtain cables, mounting hardware, and any power supplies or hubs
required by that conguration.
Make sure you are familiar with all the Included parts (see the next page) and have all the necessary tools for installing the
Cable Cubby.
Before cutting a hole in any furniture, select the best location for the EBP 1200C.
• Ensure that the product is oriented so that the lid opens in the desired direction.
• Ensure there is enough space for all the system cables and components, including cable retractors, if they are to be
installed.
Check all relevant regulations (see the next page).
Step 2 — Cutting the Table
Decide on the method for cutting a hole in the table (see Cutting the Table on page 3).
Verify that you have the correct cut-out template and dimensions (see Cutting the Table on page 3).
Step 3 — Setting the eBUS ID Address
All eBUS devices connected to the same control processor must have a unique eBUS ID address. This requires access to the
DIP switches on the bottom panel of the EBP 1200C and it is more convenient to set the address before the EBP 1200C is
installed in the table (see Setting the eBUS ID Address on page 10).
w
w
w
.
e
x
t
r
o
n
.
c
o
m