ProCurve Series 8100fl Read Me First

Download Read me first of ProCurve Series 8100fl Switch for Free or View it Online on All-Guides.com.

Brand: ProCurve

Category: Switch

Type: Read me first for ProCurve Series 8100fl

Pages: 4

Download ProCurve Series 8100fl Read me first

ProCurve Series 8100fl Read me first - Page 1
1
ProCurve Series 8100fl Read me first - Page 2
2
ProCurve Series 8100fl Read me first - Page 3
3
ProCurve Series 8100fl Read me first - Page 4
4
1
Read Me First
for the ProCurve Series 8100fl Switches Software Version CY.01.02.0050
Contents
ProCurve Series 8100fl Operation and Installation Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1
Setting the System Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1
About Your ProCurve Series 8100fl Switches Manual Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2
Software Updates Are Free! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2
Mini-GBIC Operation Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3
Open Source Software Acknowledgement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3
ProCurve Series 8100fl Operation and Installation Notes
System Clock. To ensure correct operation of your switch, you must update the system clock and
reload prior to configuration. This is required only for the initial installation and configuration of your
system. See “Setting the System Clock” on page 1 for details.
Installation Caution. To avoid personal injury or product damage, read the safety warnings and
installation precautions listed in the Installation and Getting Started Guide included with your switch.
Never attempt to mount a ProCurve Switch 8100fl unaided.
Version B mini-GBICs only. The Series 8100fl Switches do not support “A” version ProCurve
mini-GBICs. Use only ProCurve JxxxxB version mini-GBICs with your switch. See “Mini-GBIC
Operation Notes” on page 3 for details.
Scratchpad versus Running Config. Configuration commands you enter during a CLI session are
stored in a temporary location called a “scratchpad”, and do not get entered into the running
configuration until you perform a save active command. For details on saving changes to the
startup-config and running-config, refer to the Management and Configuration Guide on the
Documentation CD-ROM included with your switch.
Console Serial Port is only 9600 baud. There is no auto-baud detect on the switch. To connect a
console to the switch, configure your VT-100 terminal to operate with the following settings:
9600 baud rate/8 data bits/1 stop bit/no parity/no flow control.
Out of band Management Port. The 10/100Base-T Ethernet port on the management module is for
management only. It cannot be used for switching network traffic. The port is not auto-MDIX.
Setting the System Clock
To set the system date and time, use the clock set command from the command line interface (CLI). For more
information refer to the chapter on “Getting Started with Switch Configuration” in the Installation and Getting
Started Guide included with your switch. You can verify the clock settings using the show clock command.
For example:
Switch 8100fl#clock set 18:45:29 30 September 2005
Switch 8100fl#show clock
*18:45:29 UTC Fri September 30 2005